Jump to content
Sign in to follow this  
sugestivo

ImgBurn error - Reason: layouts do not match

Recommended Posts

Hey people!

I've been using ImgBurn for some years (since 2008), and its a great program.

But lately, i can't burn my dvd's, since the verify always return the results "Reason: Layouts do not match", and

the disc remains blank after the recording attempt.

 

Oddly, i've noticed that the burning process take much more time than before.

The normal time of recording always was about 16 minutes, but now it takes one hour and 19 minutes to "record".

After 1:19, the verify bring that error, "Reason: Layouts do not match", and the disc remains blank.

 

I don't know if it is the type of media... Im using Sony media, because they have a good quality

in video playback... But i have used others, and the result is the same.

Sometimes, i keep trying to burn, after successive errors, and at ramdom, the recording works!

I don't know why... But in order to record a disk, i usually take about 5~6 tries.

 

Please help me with some info! I've looked in other threads, but i haven't found one

with the exactly same driver and problem that i have.

 

Here are some description of the program (is important to tell you that i always have

used the "write mode" of ImgBurn):

 

TSSTcorp CDDVDW TS-L633A TM00 (SATA)

Current Profile: DVD-R

 

Disc Information:

Status: Empty

State of Last Session: Empty

Erasable: No

Free Sectors: 2.298.496

Free Space: 4.707.319.808 bytes

Free Time: 510:48:46 (MM:SS:FF)

Next Writable Address: 0

Supported Write Speeds: 3x; 4x; 6x; 8x

 

Pre-recorded Information:

Manufacturer ID: SONY16D1

 

Physical Format Information (Last Recorded):

Disc ID: 0@P-!-00

Book Type: DVD-R

Part Version: 5

Disc Size: 120mm

Maximum Read Rate: Not Specified

Number of Layers: 1

Track Path: Parallel Track Path (PTP)

Linear Density: 0.267 um/bit

Track Density: 0.74 um/track

First Physical Sector of Data Area: 196.608

Last Physical Sector of Data Area: 0

Last Physical Sector in Layer 0: 0

 

Performance (Write Speed):

Descriptor 1...

-> B0: 0x00; B1: 0x00; B2: 0x00; B3: 0x00

-> EL: 2297887 (0x0023101F)

-> RS: 11.080 KB/s (8x) - WS: 4.155 KB/s (3x)

Descriptor 2...

-> B0: 0x08; B1: 0x00; B2: 0x00; B3: 0x00

-> EL: 2297887 (0x0023101F)

-> RS: 11.080 KB/s (8x) - WS: 5.540 KB/s (4x)

Descriptor 3...

-> B0: 0x08; B1: 0x00; B2: 0x00; B3: 0x00

-> EL: 2297887 (0x0023101F)

-> RS: 11.080 KB/s (8x) - WS: 8.310 KB/s (6x)

Descriptor 4...

-> B0: 0x08; B1: 0x00; B2: 0x00; B3: 0x00

-> EL: 2297887 (0x0023101F)

-> RS: 11.080 KB/s (8x) - WS: 11.080 KB/s (8x)

 

 

Thanks for any help or info!!

 

 

Cheers,

Share this post


Link to post
Share on other sites

Try burning at all supported speeds.

 

You could try cleaning the drive with a cleaning disc.

 

Try some better discs - Verbatim or Taiyo Yuden.

 

Also use the current version of ImgBurn. (in case you are not using it already)

Share this post


Link to post
Share on other sites

Hey ianymaty, thanks for your answer!

 

I'll buy a cleaning disc, and also try to burn the images in all supported

speeds.

Im feeling really noob now, i didn't knew that Sony medias had poor quality...

I always thought that was the opposite!

 

I've just tried to burn, again, in the same media.

I'll paste the record log, so you can see if there's another problem with my recorder/pc/image/media:

 

"I 19:58:26 ImgBurn Version 2.5.5.0 started!

I 19:58:26 Microsoft Windows 7 Ultimate Edition (6.1, Build 7600)

I 19:58:26 Total Physical Memory: 3.128.496 KB - Available: 1.076.976 KB

I 19:58:26 Initialising SPTI...

I 19:58:26 Searching for SCSI / ATAPI devices...

I 19:58:29 -> Drive 1 - Info: TSSTcorp CDDVDW TS-L633A TM00 (E:) (SATA)

I 19:58:29 Found 1 DVD±RW/RAM!

I 19:58:36 Operation Started!

I 19:58:36 Source File: D:\Arquivos\A gravar\DVD\DBZ_6.iso

I 19:58:36 Source File Sectors: 2.205.896 (MODE1/2048)

I 19:58:36 Source File Size: 4.517.675.008 bytes

I 19:58:36 Source File Volume Identifier: DBZ_6

I 19:58:36 Source File Volume Set Identifier: 0061B51DDVDSHRNK

I 19:58:36 Source File Implementation Identifier: DVD Shrink

I 19:58:36 Source File File System(s): ISO9660; UDF (1.02)

I 19:58:36 Destination Device: [2:0:0] TSSTcorp CDDVDW TS-L633A TM00 (E:) (SATA)

I 19:58:36 Destination Media Type: DVD-R (Disc ID: SONY16D1) (Speeds: 3x; 4x; 6x; 8x)

I 19:58:36 Destination Media Sectors: 2.297.888

I 19:58:36 Write Mode: DVD

I 19:58:36 Write Type: DAO

I 19:58:36 Write Speed: 4x

I 19:58:36 Link Size: Auto

I 19:58:36 Lock Volume: Yes

I 19:58:36 Test Mode: No

I 19:58:36 OPC: No

I 19:58:36 BURN-Proof: Enabled

I 19:58:36 Write Speed Successfully Set! - Effective: 5.540 KB/s (4x)

I 19:58:37 Filling Buffer... (40 MB)

I 19:58:39 Writing LeadIn...

I 19:59:17 Writing Session 1 of 1... (1 Track, LBA: 0 - 2205895)

I 19:59:17 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 2205895)

I 21:13:41 Synchronising Cache...

I 21:14:29 Exporting Graph Data...

I 21:14:29 Graph Data File: C:\Users\Danilo\AppData\Roaming\ImgBurn\Graph Data Files\TSSTcorp_CDDVDW_TS-L633A_TM00_QUINTA-FEIRA-14-DE-ABRIL-DE-2011_19-58_SONY16D1_4x.ibg

I 21:14:29 Export Successfully Completed!

I 21:14:29 Operation Successfully Completed! - Duration: 01:15:53

I 21:14:29 Average Write Rate: 988 KB/s (0.7x) - Maximum Write Rate: 5.601 KB/s (4.0x)

I 21:14:29 Cycling Tray before Verify...

W 21:32:32 Waiting for device to become ready...

I 21:32:45 Device Ready!

E 21:32:46 CompareImageFileLayouts Failed! - Session Count Not Equal (1/0)

E 21:32:46 Verify Failed! - Reason: Layouts do not match."

 

Do you noticed the recording speed variation? Is that normal?

 

 

 

Thank you for you help!!

 

 

Cheers,

Edited by sugestivo

Share this post


Link to post
Share on other sites
I 21:14:29 Operation Successfully Completed! - Duration: 01:15:53

I 21:14:29 Average Write Rate: 988 KB/s (0.7x) - Maximum Write Rate: 5.601 KB/s (4.0x)

Indicates either that the burner has a very tricky work to write to those disc or that you are in PIO mode (and that's not very likely as you are in Win 7)

 

Can you attach this file to a post? It should show some more about the crappy burn.

 

I 21:14:29 Graph Data File: C:\Users\Danilo\AppData\Roaming\ImgBurn\Graph Data Files\TSSTcorp_CDDVDW_TS-L633A_TM00_QUINTA-FEIRA-14-DE-ABRIL-DE-2011_19-58_SONY16D1_4x.ibg

Share this post


Link to post
Share on other sites

Hey Cynthia! Thanks for the help!

 

That is very strange, because at ramdom, the driver works perfectly!

 

The file is going, attached! I appreciate your help!

I had to compress the file, because the forum only allow a file up to 1MB!

And that file has 1,23 MB!

 

Thank you!!

 

TSSTcorp_CDDVDW_TS-L633A_TM00_QUINTA-FEIRA-14-DE-ABRIL-DE-2011_19-58_SONY16D1_4x.rar

 

 

Cheers,

Share this post


Link to post
Share on other sites

The graph looks like it writes pretty much at 4x the whole time. Not sure how it can take ages to burn it. :wacko:

 

Only odd thing is in the start of the burn. Did it freeze at that point?

 

post-20-0-41987700-1302831806.png

Share this post


Link to post
Share on other sites

Cynthia,

 

 

Interesting!

I have to admit that i don't understand what's the problem,

just looking at it.

But i guess that would be the green line (write RPM), right?

 

That means that my driver engine is not working properly??

 

Thanks!

 

 

Cheers,

Share this post


Link to post
Share on other sites

Opti Drive Control shows it better. Looks as it falls down to zero in write speed for the whole burn period. (Look at the blue lines)

 

post-20-0-45952300-1302832933.png

Share this post


Link to post
Share on other sites

Have you tried another speed than the one above - 4x?

 

The following (in red) are the ones that are supported by the media/firmware combo::

 

I 19:58:36 Destination Media Type: DVD-R (Disc ID: SONY16D1) (Speeds: 3x; 4x; 6x; 8x)

Have you checked at your notebooks manufacturers homepage if there are any new chip set drivers for the mother board to install/update?

Share this post


Link to post
Share on other sites

Cynthia,

 

Do you think this is a hardware problem?

Or misconfigurated driver settings? Tomorrow i'll try in a different media...

Or maybe CPU usage?

 

I remember that the driver was working perfectly...

But one day, i dumbly installed DVD43... When i noticed that wasn't working,

i uninstalled DVD43, and restored windows to a point before DVD43 install.

And the recording worked again... for a short period... after that, the recording

started to "fade" again...

 

A friend told me that this could be a registry problem.

I installed "RegCure", and fixed many errors, but the driver recording didn't changed.

Do you have any knowledge about that problem is associated with DVD43?

How could i restore the driver functions?

 

 

This is a hard problem! Thank you for you time and effort!!

 

 

 

Cheers!

Share this post


Link to post
Share on other sites

Hey Cynthia!

 

I always burned discs at 1x (ignorance). I always thought that

lower speeds meant perfect playback. I'm trying right now, to burn at those supported speeds!

 

In the manufacturer's homepage, there's not a specific driver for the CD/DVD recorder (look, im attaching).

 

post-38714-0-30655500-1302834842.png

 

There's only for Video, Audio, Modem, OSD, Network, Touchpad and wireless... isn't that strange?

There should be a driver for the recorder... but i remember that when i installed this OS, the driver

was recognized by the system.... Maybe there is a old driver controlling the recorder?! Maybe this is the answer?

I think i will look into TSSTcorp website for a new driver... What do you recommend?

If i found it, i can install it right away? Or maybe i should uninstall the old one?

 

Edit: I just found a website that can scan the driver and download a new one

My link

Can i trust this? The TSSTcorp website is total crap, only have a generic OEM driver for download.

 

Thank you!

 

Have you tried another speed than the one above - 4x?

 

The following (in red) are the ones that are supported by the media/firmware combo::

 

I 19:58:36 Destination Media Type: DVD-R (Disc ID: SONY16D1) (Speeds: 3x; 4x; 6x; 8x)

Have you checked at your notebooks manufacturers homepage if there are any new chip set drivers for the mother board to install/update?

Edited by sugestivo

Share this post


Link to post
Share on other sites

If the driver for DVD43 still was running, you should see a warning row for that in the log.

 

You can check in

 

Main Menu -> Tools -> Filter Driver Load Order...

 

If that driver is still installed. You can also post the info in a posting window here. Just press the Copy To Clipboard button and paste the text into here.

Share this post


Link to post
Share on other sites

Cynthia,

 

 

Here it is!

Seems that DVD43 isn't the problem...

 

===============================================

Filter Driver Load Order - ImgBurn v2.5.5.0

===============================================

 

Upper Device Filter: [None Found]

Upper Class Filter: [None Found]

Device: CD/DVD-ROM Device

Lower Class Filter: [None Found]

Lower Device Filter: [None Found]

 

 

 

 

If the driver for DVD43 still was running, you should see a warning row for that in the log.

 

You can check in

 

Main Menu -> Tools -> Filter Driver Load Order...

 

If that driver is still installed. You can also post the info in a posting window here. Just press the Copy To Clipboard button and paste the text into here.

Share this post


Link to post
Share on other sites

Hello, ianymaty and Cynthia!

Good mourning to you!

 

 

I've just tried the site you linked here, ianymaty

Take a look at the results for the CD/DVD drive:

 

Drive de CD/DVD 1

Informações gerais

 

Nome do Driver (Driver name):

TSSTcorp CDDVDW TS-L633A ATA Device

 

Descrição do driver (driver description):

CD-ROM Drive

 

Versão do driver (driver version):

6.1.7600.16385

 

Local do a rquivo .INF (Location of .INF file):

cdrom.inf

 

Fabricante do driver (Driver's manufacturer):

Microsoft

 

Informações MMC (MMC Info):

Fabricante (Manufacturer):

TSSTcorp

Produto (Product):

CDDVDW TS-L633A

Revisão (Review):

TM00

Tam. do Buffer (Buffer size):

2048 Ko

Veloc. atual de leitura (Current reading speed):

8X (DVD)

Veloc. atual de gravação (Current recording speed):

8X (DVD)

Veloc. Máx. de leitura (Maximum reading speed):

8X (DVD)

Veloc. Máx. de gravação (Maximum recording speed):

8X (DVD)

 

Tipo (Type):

DVD-R/DL sequential recording Recorder

Número de série (Serial number):

TS-L633AFirmware

 

The section "driver resources" got all messed up here in the forum,

so i took a snapshot here: post-38714-0-69403700-1302875859.png

 

But in the report i found it strange when it says:

Manufacturer: Microsoft

And after that, it says the manufacturer is TSSTcorp

 

I guess i'll try to burn at 8x speed now...

 

Summary of the solutions you have pointed me:

1 - Try to burn at all supported speeds (trying right now)

2 - Use a cleaning disc (not tried yet - i'll get one today)

3 - Try better media, aka Verbatim or Taiyo Yuden (not tried yet - i'll get today)

4 - Check in manufacturer's site for a new driver (i haven't found a more updated driver yet, on TSSTcorp or in CCE homepage - the CPU assembler. But i think im gonna give a try on http://driversfinder.net/drivers/tsstcorp-cddvdw-ts-l633a-ata-device and http://www.ma-config.com. Those sites have an "driver updater tool". Im gonna try them both).

 

 

Im gonna try those solutions today, and after, i'll post what i got here, for you!

Thanks for the help and patience!

 

 

Cheers,

Share this post


Link to post
Share on other sites

Did you press the green window button in the upper left corner of the image you posted - to update the drivers?

Share this post


Link to post
Share on other sites

Hey people!

What info "title" should i post here?

Under the guide "Software", and "Drivers", i found more info about the driver.

The driver for CD/DVD is from 21/06/2006. Cynthia, i have tried the green button,

but the site doesn't have a update/suggestion for the CD/DVD driver.

 

Did you press the green window button in the upper left corner of the image you posted - to update the drivers?

Share this post


Link to post
Share on other sites

After you clicked the green buton to find drivers, it will show a list and the drivers need update will be expanded.

 

Post that screen so we can guide you. Don't mind the CD/DVD driver, that is generic and will work on every system.

Share this post


Link to post
Share on other sites
Sign in to follow this  

×

Important Information

By using this site, you agree to our Terms of Use.