Jump to content
Sign in to follow this  
truelies

zeroing Sections stay 52% for one hour

Recommended Posts

Tried to burn a BD-RE, does this a software problem? My blu ray writer is new and firmware is corrent, I am using a Verbatim BD-RE.

Share this post


Link to post
Share on other sites

Now I burned the disc, but at the verify stage. It showes "W 18:46:19 Failed to Read Sectors 12219392 - 12219423 - Reason: L-EC Uncorrectable Error". My Blu ray write is new & disk is Verbatim also new.

Share this post


Link to post
Share on other sites

I tried to Erease data->full, got following,

 

I 10:44:26 ImgBurn Version 2.5.7.0 started!

I 10:44:26 Microsoft Windows 7 Ultimate x64 Edition (6.1, Build 7601 : Service Pack 1)

I 10:44:26 Total Physical Memory: 25,156,728 KB - Available: 21,506,636 KB

I 10:44:26 Initialising SPTI...

I 10:44:26 Searching for SCSI / ATAPI devices...

I 10:44:26 -> Drive 1 - Info: DTSOFT BDROM 1.05 (I:) (Virtual)

I 10:44:26 -> Drive 2 - Info: HL-DT-ST BD-RE WH10LS30 1.01-A0 (H:) (ATA)

I 10:44:26 -> Drive 3 - Info: HL-DT-ST DVD+-RW GH30N A102-08 (G:) (ATA)

I 10:44:26 Found 1 DVD±RW/RAM, 1 BD-ROM and 1 BD-RE!

I 10:49:47 Operation Started!

I 10:49:47 Device: [3:0:0] HL-DT-ST BD-RE WH10LS30 1.01 (H:) (ATA)

I 10:49:47 Media Type: BD-RE (Disc ID: VERBAT-IM1-000)

I 10:49:47 Media Supported Write Speeds: 2x

I 10:49:47 Quick Erase: No

I 10:49:47 Format Properly: Yes

I 10:49:47 Format Size: Preferred

I 10:49:47 Format With Full Certification: Yes

I 10:49:47 Format Without Spare Areas: Yes

I 10:49:47 Erasing Disc...

I 13:32:08 Operation Successfully Completed! - Duration: 02:42:21

I 13:32:08 Operation Started!

I 13:32:08 Device: [3:0:0] HL-DT-ST BD-RE WH10LS30 1.01 (H:) (ATA)

I 13:32:08 Media Type: BD-RE (Disc ID: VERBAT-IM1-000)

I 13:32:08 Media Supported Write Speeds: 2x

I 13:32:08 Media Sectors: 24,438,784

I 13:32:08 BD-RE FastWrite: No

I 13:32:08 Zeroing Sectors...

I 15:05:41 Synchronising Cache...

E 15:06:18 Synchronise Cache Failed! - Reason: Write Error

E 15:06:18 Failed to Erase Disc! - Reason: Write Error

E 15:06:18 Operation Failed! - Duration: 01:34:10 - Total Duration: 04:16:31

 

Why I got 'E 15:06:18 Synchronise Cache Failed! - Reason: Write Error'?

Share this post


Link to post
Share on other sites

Your drive has a problem with the disc and reported a 'Write Error'. Give it another go.

 

If it still does the same thing, try another disc.

 

If it still does the same thing, try cleaning the drive with a cleaning disc (and then try full erasing both discs again).

 

If it still does the same thing after that, get another drive.

Share this post


Link to post
Share on other sites

Thanks. I tried another drive. got

 

I 10:44:26 ImgBurn Version 2.5.7.0 started!

I 10:44:26 Microsoft Windows 7 Ultimate x64 Edition (6.1, Build 7601 : Service Pack 1)

I 10:44:26 Total Physical Memory: 25,156,728 KB - Available: 21,506,636 KB

I 10:44:26 Initialising SPTI...

I 10:44:26 Searching for SCSI / ATAPI devices...

I 10:44:26 -> Drive 1 - Info: DTSOFT BDROM 1.05 (I:) (Virtual)

I 10:44:26 -> Drive 2 - Info: HL-DT-ST BD-RE WH10LS30 1.01-A0 (H:) (ATA)

I 10:44:26 -> Drive 3 - Info: HL-DT-ST DVD+-RW GH30N A102-08 (G:) (ATA)

I 10:44:26 Found 1 DVD±RW/RAM, 1 BD-ROM and 1 BD-RE!

I 10:49:47 Operation Started!

I 10:49:47 Device: [3:0:0] HL-DT-ST BD-RE WH10LS30 1.01 (H:) (ATA)

I 10:49:47 Media Type: BD-RE (Disc ID: VERBAT-IM1-000)

I 10:49:47 Media Supported Write Speeds: 2x

I 10:49:47 Quick Erase: No

I 10:49:47 Format Properly: Yes

I 10:49:47 Format Size: Preferred

I 10:49:47 Format With Full Certification: Yes

I 10:49:47 Format Without Spare Areas: Yes

I 10:49:47 Erasing Disc...

I 13:32:08 Operation Successfully Completed! - Duration: 02:42:21

I 13:32:08 Operation Started!

I 13:32:08 Device: [3:0:0] HL-DT-ST BD-RE WH10LS30 1.01 (H:) (ATA)

I 13:32:08 Media Type: BD-RE (Disc ID: VERBAT-IM1-000)

I 13:32:08 Media Supported Write Speeds: 2x

I 13:32:08 Media Sectors: 24,438,784

I 13:32:08 BD-RE FastWrite: No

I 13:32:08 Zeroing Sectors...

I 15:05:41 Synchronising Cache...

E 15:06:18 Synchronise Cache Failed! - Reason: Write Error

E 15:06:18 Failed to Erase Disc! - Reason: Write Error

E 15:06:18 Operation Failed! - Duration: 01:34:10 - Total Duration: 04:16:31

W 16:37:24 Device Arrival Detected!

I 16:37:24 Searching for SCSI / ATAPI devices...

I 16:37:24 -> Drive 1 - Info: DTSOFT BDROM 1.05 (I:) (Virtual)

I 16:37:25 -> Drive 2 - Info: HL-DT-ST BD-RE WH10LS30 1.01-A0 (H:) (ATA)

W 16:37:25 Device Arrival Detected!

W 16:37:25 The device list will be refreshed at the next available opportunity.

I 16:37:25 -> Drive 3 - Info: HL-DT-ST DVD+-RW GH30N A102-08 (G:) (ATA)

I 16:37:25 Found 1 DVD±RW/RAM, 1 BD-ROM and 1 BD-RE!

I 16:37:25 Searching for SCSI / ATAPI devices...

I 16:37:25 -> Drive 1 - Info: DTSOFT BDROM 1.05 (I:) (Virtual)

I 16:37:26 -> Drive 2 - Info: HL-DT-ST BD-RE WH10LS30 1.01-A0 (H:) (ATA)

I 16:37:26 -> Drive 3 - Info: HL-DT-ST DVD+-RW GH30N A102-08 (G:) (ATA)

I 16:37:26 -> Drive 4 - Info: TSSTcorp BDDVDW SE-506AB TS01 (N:) (USB)

I 16:37:26 Found 1 DVD±RW/RAM, 1 BD-ROM, 1 BD-RE and 1 BD-RE XL!

I 16:39:21 Operation Started!

I 16:39:21 Device: [0:0:0] TSSTcorp BDDVDW SE-506AB TS01 (N:) (USB)

I 16:39:21 Media Type: BD-RE (Disc ID: VERBAT-IM1-000)

I 16:39:21 Media Supported Write Speeds: 2x

I 16:39:21 Quick Erase: No

I 16:39:21 Format Properly: Yes

I 16:39:21 Format Size: Preferred

I 16:39:21 Format With Full Certification: Yes

I 16:39:21 Format Without Spare Areas: Yes

I 16:39:22 Erasing Disc...

I 16:40:29 Operation Successfully Completed! - Duration: 00:01:07

I 16:40:29 Operation Started!

I 16:40:29 Device: [0:0:0] TSSTcorp BDDVDW SE-506AB TS01 (N:) (USB)

I 16:40:29 Media Type: BD-RE (Disc ID: VERBAT-IM1-000)

I 16:40:29 Media Supported Write Speeds: 2x

I 16:40:29 Media Sectors: 24,438,784

I 16:40:29 BD-RE FastWrite: No

I 16:40:29 Zeroing Sectors...

W 17:26:10 Failed to Zero Sectors 12744832 - 12744863 - Reason: Write Error

W 17:26:10 Retrying (1 of 20)...

I 17:26:10 Zeroing Sectors...

W 17:26:10 Failed to Zero Sectors 12745952 - 12745983 - Reason: Power Calibration Area Error

W 17:26:10 Retrying (1 of 20)...

I 17:26:10 Zeroing Sectors...

W 17:26:10 Failed to Zero Sectors 12747072 - 12747103 - Reason: Power Calibration Area Error

W 17:26:10 Retrying (1 of 20)...

I 17:26:10 Zeroing Sectors...

W 17:26:10 Failed to Zero Sectors 12748192 - 12748223 - Reason: Power Calibration Area Error

W 17:26:10 Retrying (1 of 20)...

I 17:26:10 Zeroing Sectors...

 

What's the reason for "Power Calibration Area Error"?

Share this post


Link to post
Share on other sites

It all boils down to your drive not liking the discs.

 

I can't tell you why it has a problem with them, only that is has. The error messages you see there in the log are exactly what the drive returns to the program when it fails to do what has been asked of it (i.e. write zeroes to some sectors).

Share this post


Link to post
Share on other sites

It all boils down to your drive not liking the discs.

 

I can't tell you why it has a problem with them, only that is has. The error messages you see there in the log are exactly what the drive returns to the program when it fails to do what has been asked of it (i.e. write zeroes to some sectors).

 

Looks like not like DVD-RW, the BD-RE is more difficult to write.

Share this post


Link to post
Share on other sites

For the

Your drive has a problem with the disc and reported a 'Write Error'. Give it another go.

 

If it still does the same thing, try another disc.

 

If it still does the same thing, try cleaning the drive with a cleaning disc (and then try full erasing both discs again).

 

If it still does the same thing after that, get another drive.

 

For this 'Write Error', how can a disk already finished writting Zero to each sector, that approves every sector can be written, then turned to 'can't write'? Looks weired.

Edited by truelies

Share this post


Link to post
Share on other sites

Sorry, I don't follow you.

 

It hasn't finished zeroing the sectors, that's what's failing to complete successfully.

 

When it goes to 99% of zeroing sectors, it began to Synchronise Cache, then it failed. What does 'Synchronise Cache'mean?

E 22:24:56 Synchronise Cache Failed! - Reason: Write Error

E 22:24:56 Failed to Erase Disc! - Reason: Write Error

E 22:24:56 Operation Failed! - Duration: 01:34:09 - Total Duration: 04:13:10

Share this post


Link to post
Share on other sites

Sync cache is what always happens at the end of a burn. It's where the drive is told to finish performing everything it has been told to do up until that point - because don't forget, drives have an internal buffer.

 

So even though the program may have (successfully) sent all the data to the drive for writing, the drive won't actually have tried to write it to the disc until it has finished writing everything in its internal buffer (cache).

 

The sync cache command signals the end of the burn so anything else the drive needs to do to the disc in order to make it work properly later on is also done at that point. Your drive reported a 'Write Error' whilst trying to perform those functions.

Share this post


Link to post
Share on other sites

Sync cache is what always happens at the end of a burn. It's where the drive is told to finish performing everything it has been told to do up until that point - because don't forget, drives have an internal buffer.

 

So even though the program may have (successfully) sent all the data to the drive for writing, the drive won't actually have tried to write it to the disc until it has finished writing everything in its internal buffer (cache).

 

The sync cache command signals the end of the burn so anything else the drive needs to do to the disc in order to make it work properly later on is also done at that point. Your drive reported a 'Write Error' whilst trying to perform those functions.

 

Today I tried CDburnerXP, it works for same disc and drive. It passed the verifiy, I watched all the movie, no problem. Maybe Imgburn not fit well for BD-RE?

Share this post


Link to post
Share on other sites

Others programs don't all erase like ImgBurn and don't catch all the errors ImgBurn does.

 

That's especially true of programs that don't do their own drive I/O and rely a 3rd party burning library.

 

At the end of the day, the drive has complete control over these things so what fails in one program will fail in another too. You just have to make sure you're comparing apples with apples and not with oranges.

 

You can see here that ImgBurn works just fine with BD discs when the hardware / media do what's asked of them.

 

http://forum.imgburn.com/index.php?showtopic=16152

Share this post


Link to post
Share on other sites

Others programs don't all erase like ImgBurn and don't catch all the errors ImgBurn does.

 

That's especially true of programs that don't do their own drive I/O and rely a 3rd party burning library.

 

At the end of the day, the drive has complete control over these things so what fails in one program will fail in another too. You just have to make sure you're comparing apples with apples and not with oranges.

 

You can see here that ImgBurn works just fine with BD discs when the hardware / media do what's asked of them.

 

http://forum.imgburn.com/index.php?showtopic=16152

 

I problem is the movie plays great and also passed the verification using other software. Maybe the imgburn is better but the drive is too tough?

Share this post


Link to post
Share on other sites

Like I said, you need to be making a fair comparison and you might not be.

 

You can enable something called 'spare areas' when formatting a disc which in turn enables a drive's 'Defect Management'. That can help to overcome bad sectors by remapping them to the 'spare areas' on the disc.

 

ImgBurn defaults to formatting without spare areas because it frees up more space on the disc that can then be used for user data.

Share this post


Link to post
Share on other sites

Like I said, you need to be making a fair comparison and you might not be.

 

You can enable something called 'spare areas' when formatting a disc which in turn enables a drive's 'Defect Management'. That can help to overcome bad sectors by remapping them to the 'spare areas' on the disc.

 

ImgBurn defaults to formatting without spare areas because it frees up more space on the disc that can then be used for user data.

 

The Imgburn's drive may have difficulty on some blu ray disk or drive. It read the disk data as 0x00 when verify, actually it has data inside, so it compatibility maybe not so good. I belive it maybe already wrote data to the disc, but can't pass verify. Also the 'erease data' maybe have problem too, after find finished 99%(maybe 100%) of zero sectors, then stopped at 'sync cache'.

Share this post


Link to post
Share on other sites

There is no problem with any of that stuff in the program itself. Such problems would cause issues for everyone and that simply isn't the case.

 

It's down to your drive to do what's asked of it. If it returns errors / incorrect info then that's totally out of my hands.

Share this post


Link to post
Share on other sites
Sign in to follow this  

×

Important Information

By using this site, you agree to our Terms of Use.