Jump to content

pumplewis

Members
  • Content Count

    17
  • Joined

  • Last visited

About pumplewis

  • Rank
    ISF Newbie
  1. pumplewis

    io error

    Dont worry about it. Put a new burner in and it works perfectly. Thanks.
  2. pumplewis

    io error

    It is weird....Since I updated the firmware the % of completion moves (very sow, takes 6 hours to complete) and it never did that before with these discs however the device buffer never moves. It stays at 0 the whole time. The "buffer" starts at 100 and stays there for a few minutes (5-10) then drope down to about 53 %. It takes for ever to try and go on the internet or do anything on the computer when I am burning. The burning aso gives me the same error as before after its done (6 hours later). Before I updated the firmware it would just give me the error right away and show 0% for completion the whole time and the rest of my computer would run normal. I also find that when I try and burn now that my Virus scan comes on and starts scanning my computer and I cant close it until I stop the burn. I cant find the computer usage in controll panel, part of the problem is that the computer runs so slow it takes to long to do anything. I hope this helps to give you an idea of the problem............
  3. pumplewis

    io error

    Not sure I undrstand your question properly....Image burn is the only program running and the nothing else is being used when I try and burn. Is that what you mean?
  4. pumplewis

    io error

    I followed all of your instructions but still had no luck.......
  5. pumplewis

    io error

    I went to my system manager and found it was already set to dma (automatic) in the ide controllers branch. I also set my 'Transfer Length' option to 'Manual' instead of 'Automatic' and put it on '32 KB' instead of '64 KB'. It still does the same thing when I try and burn. It is very SLOW...... It takes about 6 hours and when its done the same error comes up as I mentioned at the start of this post. The disc obviously wont work either. I aso have found that since I updated my firmware that when I try and burn my computer becomes increadably slow. Almost to the point where I cant use it. I think it is the burner but if you have another idea for me to try I am all for it! anything to save a buck lol. Thanks.
  6. pumplewis

    io error

    I went to my system manager and found it was already set to dma (automatic) in the ide controllers branch. I also set my 'Transfer Length' option to 'Manual' instead of 'Automatic' and put it on '32 KB' instead of '64 KB'. It still does the same thing when I try and burn. It is very SLOW...... It takes about 6 hours and when its done the same error comes up as I mentioned at the start of this post. The disc obviously wont work either. I aso have found that since I updated my firmware that when I try and burn my computer becomes increadably slow. Almost to the point where I cant use it. I think it is the burner but if you have another idea for me to try I am all for it! anything to save a buck lol. Thanks.
  7. pumplewis

    io error

    Thanks for the link. I updated the firmware and my burner appeared to start burning however it did so vey slow. It took about 6 hours lol... I had the speed set at 8x. I think this burner is out of date and ready for the garbage lol. I will stop tortureing myself and buy a new one. Thats got to be the problem............Thanks.
  8. pumplewis

    io error

    I am trying to find an update for my benq dw 822a but cant get anything, The link above will not open. Does anyone have an update for my firmware that will open and work? Any help would be greatly appreciated. Thanks.
  9. pumplewis

    io error

    Ok thanks for the help I will try and find an updated firmware. If that doesnt work I will buy a new burner. Thanks again.
  10. pumplewis

    io error

    Ok so your saying its my burner?
  11. pumplewis

    io error

    Destination Media Type: DVD-R (Disc ID: RITEKF1) (Speeds: 2.4x, 4x). This is what it says for his disc.
  12. pumplewis

    io error

    I think you mean the discs suck! Is this what your saying?
  13. pumplewis

    io error

    What do you mean? I am new to all of this stuff lol.
  14. pumplewis

    io error

    I think I may have answered my own question here..... My friend just let me try one of his discs (the same kind I was using) and it worked. Does it make sence that I have a bad batch of discs?
  15. pumplewis

    io error

    I am new to this lol. Are you saying I should try a different kind of disc?
×

Important Information

By using this site, you agree to our Terms of Use.