Jump to content

OPC failed & Burnspeed-Bug


FlYeRoNe

Recommended Posts

I 18:00:11 ImgBurn Version 2.4.1.0 started!

I 18:00:11 Microsoft Windows XP Professional (5.1, Build 2600 : Service Pack 2)

I 18:00:11 Total Physical Memory: 3,406,240 KB - Available: 2,985,544 KB

W 18:00:11 Drive F:\ (FAT32) does not support single files > 4 GB in size.

I 18:00:11 Initialising SPTI...

I 18:00:11 Searching for SCSI / ATAPI devices...

I 18:00:11 Found 1 DVD-ROM, 1 DVD

Link to comment
Share on other sites

Fine on mine and given that it went over network and to a Usb drive @ that, the speed it reached is (acceptable) especially as network and usb do not mix.

How LIGHTNING UK says my ideas out. This is the one and only burner from the BenQ-Company with such problems. All my other BenQ burner and Pioneer and Plextor's have not such problems with ImgBurn. Only these two DW1650 make me problems.

 

I have no ideas where i searching my problems!

Link to comment
Share on other sites

I 18:01:50 Writing LeadIn...
I 18:01:52 Writing Session 1 of 1... (1 Track, LBA: 0 - 2285847)

Why needs my DW1650 37sec's to write the LeadIn and yours only 2seconds? This is a huge difference!

I 14:20:16 Writing LeadIn...
I 14:20:53 Writing Session 1 of 1... (1 Track, LBA: 0 - 2285455)

Is this maybe a criterion for my problems?

Link to comment
Share on other sites

your drive failed with OPC Enabled mine did not, thats why it was quicker.

 

 

btw did you uninstall the enhanced host controller from device manager under universal serial bus controllers.

 

it will detect your hardware again on a reboot / best to restart even if it finds new hardware straight away b4 reboot, you could try changing the usb cable as well.

 

Not likely either of those are at fault but my usb has stuck at 4x b4 long time ago and only fix was to unistall EHCI (the enhanced port)

 

 

another thing to try maybe power supply to your enclosure is not the right one and does not have enough ampage as not all external drive power supplies are the same.(especially if you have a few different makes you may have mixed up the PSU's)

 

also if your enclosure uses prolific 3507 chip update the firmware in enclosure as if i remember rightly there was an issue with Benq drives and I think the 1650 which a firmware update to enclosure fixed.

 

 

[edit] i just looked at prolific firmware and it was a benq 1640 and another benq but not 1650) still if you are using enclosure with pl3507 it might help to make sure chipset is up to date.

 

Another thing make sure you have any drive in any enclosure set to master and not slave and that it is using 80 wire short ide cable.

Link to comment
Share on other sites

In this part of my log have i am OPC disabled.

.

.

.

I 14:20:07 Source File: -==/\/[bUILD IMAGE]\/\==-

I 14:20:07 Source File Sectors: 2.285.456 (MODE1/2048)

I 14:20:07 Source File Size: 4.680.613.888 bytes

I 14:20:07 Source File Volume Identifier: The Crow 1994 HD2DVD

I 14:20:07 Source File Application Identifier: ImgBurn V2.4.1.0

I 14:20:07 Source File Implementation Identifier: ImgBurn

I 14:20:07 Source File File System(s): ISO9660; UDF (1.02)

I 14:20:07 Destination Device: [0:0:0] BENQ DVD DD DW1650 BCDC (K:) (USB)

I 14:20:07 Destination Media Type: DVD+R (Disc ID: MCC-004-00) (Speeds: 4x; 8x; 12x; 16x)

I 14:20:07 Destination Media Sectors: 2.295.104

I 14:20:07 Write Mode: DVD

I 14:20:07 Write Type: DAO

I 14:20:07 Write Speed: 8x

I 14:20:07 Link Size: Auto

I 14:20:07 Test Mode: No

I 14:20:08 OPC: No

I 14:20:08 BURN-Proof: Enabled

.

.

.

I 14:20:14 Filling Buffer... (40 MB)

I 14:20:16 Writing LeadIn...

I 14:20:53 Writing Session 1 of 1... (1 Track, LBA: 0 - 2285455)

I 14:20:53 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 2285455)

I 14:35:42 Synchronising Cache...

 

My DW1650 needs however 37sec for write LeadIn! When i activate OPC in ImgBurn came this Failed-Message:

E 14:18:07 Optimum Power Calibration Failed! - Reason: Track Following Error

 

I can not activate this option without this Error-Message comes. All my other BenQ-Drives to performed with this option.

 

[EDIT]

I tested this OverSpeed funktions...I'll be back later.

Edited by FlYeRoNe
Link to comment
Share on other sites

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.