Jump to content

Multiple errors!


willryan42

Recommended Posts

So lately I've been using osx360 to burn my games. I haven't burned one in a couple weeks, but when I did it yesterday, it burned fine, but when i put it into my xbox, it doesn't play. No error message, just tries to read it, makes some weird noises and then goes to the dashboard.

 

I also tried burning in iburn360 and the same noises happen and then to the dashboard.

 

Then I went to imgburn. I've burned over 40 games with imgburn under parallels desktop without a hiccup, even though I've been using memorex dl discs. But this time, I get a few errors. First "failed to set L0 data zone capacity! reason: medium not present" then same L0 error with "reason: power on, reset, or bus device reset occurred" then "reason: invalid field in parameter list"

 

I 22:23:20 Operation Started!

I 22:23:20 Source File: \\.PSF\.Home\Downloads\xxx-sto.iso

I 22:23:20 Source File Sectors: 3,825,924 (MODE1/2048)

I 22:23:20 Source File Size: 7,835,492,352 bytes

I 22:23:20 Source File Volume Identifier: XGD2DVD_NTSC

I 22:23:20 Source File Volume Set Identifier: 34672923

I 22:23:20 Source File Implementation Identifier: Sonic Scenarist 3.1

I 22:23:20 Source File File System(s): ISO9660, UDF (1.02)

I 22:23:20 Destination Device: [0:1:0] HL-DT-ST DVDRW GSA-S10N BP10 (D:) (ATA)

I 22:23:20 Destination Media Type: DVD+R DL (Disc ID: RITEK-S04-66) (Speeds: 2.4x, 4x)

I 22:23:20 Destination Media Sectors: 4,173,824

I 22:23:20 Write Mode: DVD

I 22:23:20 Write Type: DAO

I 22:23:20 Write Speed: 2.4x

I 22:23:20 Link Size: Auto

I 22:23:20 Test Mode: No

I 22:23:20 OPC: No

I 22:23:20 BURN-Proof: Enabled

I 22:23:20 Book Type Setting: N/A

I 22:23:20 User Specified L0 Data Zone Capacity: 1,913,760

E 22:32:04 Failed to set L0 Data Zone Capacity!

E 22:32:04 Reason: Invalid Field in Parameter List

E 22:32:04 Operation Failed! - Duration: 00:08:44

I 22:32:04 Average Write Rate: N/A - Maximum Write Rate: N/A

 

 

Is it possible that I have some bad DL discs? I know everyone here is verbatim crazy, but I have a 50 pack of these memorex's and I've never had a problem with them before.

 

Also, I have a toshiba laptop and the games burn fine in imgburn on there. Could it be something with my drive on the macbook? It's pretty new, and cd's and dvd's still burn fine, just trouble with DL's.

Link to comment
Share on other sites

I've tried both 2.4 and 4x.

 

Here's a log of when I just continue pass the errors:

 

I 22:43:04 Operation Started!

I 22:43:04 Source File: \\.PSF\.Home\Downloads\xxx-sto.iso

I 22:43:04 Source File Sectors: 3,825,924 (MODE1/2048)

I 22:43:04 Source File Size: 7,835,492,352 bytes

I 22:43:04 Source File Volume Identifier: XGD2DVD_NTSC

I 22:43:04 Source File Volume Set Identifier: 34672923

I 22:43:04 Source File Implementation Identifier: Sonic Scenarist 3.1

I 22:43:04 Source File File System(s): ISO9660, UDF (1.02)

I 22:43:04 Destination Device: [0:1:0] HL-DT-ST DVDRW GSA-S10N BP10 (D:) (ATA)

I 22:43:04 Destination Media Type: DVD+R DL (Disc ID: RITEK-S04-66) (Speeds: 2.4x, 4x)

I 22:43:04 Destination Media Sectors: 4,173,824

I 22:43:04 Write Mode: DVD

I 22:43:04 Write Type: DAO

I 22:43:04 Write Speed: 2.4x

I 22:43:04 Link Size: Auto

I 22:43:04 Test Mode: No

I 22:43:04 OPC: No

I 22:43:04 BURN-Proof: Enabled

I 22:43:04 Book Type Setting: N/A

I 22:43:04 User Specified L0 Data Zone Capacity: 1,913,760

W 22:44:16 Failed to set L0 Data Zone Capacity!

W 22:44:16 Reason: Medium Not Present

I 22:44:27 Filling Buffer... (20 MB)

I 22:44:28 Writing LeadIn...

I 22:44:37 Writing Session 1 of 1... (1 Track, LBA: 0 - 3825923)

I 22:44:37 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 3825923)

I 22:44:37 Writing Layer 0... (LBA: 0 - 2086911)

I 22:45:29 Abort Request Acknowledged

I 22:45:29 Synchronising Cache...

W 22:45:32 User opted to skip the 'Close Track/Session/Disc' functions.

E 22:45:32 Failed to Write Image!

I 22:45:32 Exporting Graph Data...

I 22:45:32 Graph Data File: C:\Documents and Settings\Administrator\Application Data\ImgBurn\Graph Data Files\HL-DT-ST_DVDRW_GSA-S10N_BP10_MONDAY-MARCH-16-2009_10-43_PM_RITEK-S04-66_2.4x.ibg

I 22:45:32 Export Successfully Completed!

E 22:45:32 Operation Aborted! - Duration: 00:02:27

Link to comment
Share on other sites

Can you please copy + paste the disc info from the panel on the right when you're in Read mode with that disc in the drive... thanks!

 

Oh and because of this thread (and a suggestion made by a beta team member a while back!) I've added code to log the error codes on all the 'retries' you (the user) perform when the program is trying to set the layer break position.

 

Obviously some important ones are missing from the log here because 'medium not present' is a really weird one to run into mid way through doing something - so it probably followed a bus reset - which you mentioned in your initial post but wasn't logged anywhere.

Link to comment
Share on other sites

heres the disc info:

 

HL-DT-ST DVDRW GSA-S10N BP10 (ATA)

Current Profile: DVD+R DL

 

Disc Information:

Status: Empty

Erasable: No

Free Sectors: 4,173,824

Free Space: 8,547,991,552 bytes

Free Time: 927:32:74 (MM:SS:FF)

 

Disc Control Blocks Information:

HL-DT-ST GSA-S10N

 

Physical Format Information (Last Recorded - L0):

Disc ID: RITEK-S04-66

Book Type: DVD+R DL

Part Version: 1

Disc Size: 120mm

Maximum Read Rate: Not Specified

Number of Layers: 2

Track Path: Opposite Track Path (OTP)

Linear Density: 0.293 um/bit

Track Density: 0.74 um/track

First Physical Sector of Data Area: 196,608

Last Physical Sector of Data Area: 16,580,607

Last Physical Sector in Layer 0: 2,283,519

 

Physical Format Information (Last Recorded - L1):

Disc ID: RITEK-S04-66

Book Type: DVD+R DL

Part Version: 1

Disc Size: 120mm

Maximum Read Rate: Not Specified

Number of Layers: 2

Track Path: Opposite Track Path (OTP)

Linear Density: 0.293 um/bit

Track Density: 0.74 um/track

First Physical Sector of Data Area: 196,608

Last Physical Sector of Data Area: 16,580,607

Last Physical Sector in Layer 0: 2,283,519

 

 

 

and i dont know about the log, i copied everything that's there, unless theres some setting i need to change?

Link to comment
Share on other sites

Can you please post that information from the Write mode too? Your log shows the burn being aborted less than a minute after being started, so that disc was probably damaged in the aborted burn.

Link to comment
Share on other sites

Here's the log from the write mode with a new disc:

 

HL-DT-ST DVDRW GSA-S10N BP10 (ATA)

Current Profile: DVD+R DL

 

Disc Information:

Status: Empty

Erasable: No

Free Sectors: 4,173,824

Free Space: 8,547,991,552 bytes

Free Time: 927:32:74 (MM:SS:FF)

Supported Write Speeds: 2.4x, 4x

 

DVD

Link to comment
Share on other sites

Thanks for your help! I'm going to pick up a few verbatim's tomorrow and test it out.

 

Dual layer disc's seem to be different than regular blank cd's and dvd's am I right? For example, with just cd-r's and dvd-r's, I can use any brand at all with no problems. But i obviously have problems with certain brands of DL discs. Normal?

Link to comment
Share on other sites

I 13:54:16 ImgBurn Version 2.4.2.0 started!

I 13:54:16 Microsoft Windows XP Professional (5.1, Build 2600 : Service Pack 2)

I 13:54:16 Total Physical Memory: 523,828 KB - Available: 386,452 KB

I 13:54:16 Initialising SPTI...

I 13:54:16 Searching for SCSI / ATAPI devices...

I 13:54:16 Found 1 DVD

Link to comment
Share on other sites

Dumb question as I know nothing about todays Mac's. Over fifteen years since I owned one.

 

Do you run ImgBurn through some windows emulator software or is Windows just installed on this computer as on any ordinary (real) Windows computer?

Link to comment
Share on other sites

I run it through Parallels desktop, which yes, is an emulator. And I can't see this being a problem, because I've burned countless number of dual layers under parallels with this computer, then I stopped for a month or so and when i tried again, I'm greeted by this mess =/

Link to comment
Share on other sites

Apparently that didn't work:

 

W 04:39:21 I/O Interface has been changed!

I 04:39:21 Shutting down SPTI...

I 04:39:21 Initialising ASPI...

E 04:39:21 Unable to initialise ASPI! - WNASPI32.DLL

E 04:39:21 Reason: The specified module could not be found.

E 04:39:21 You need to install an ASPI manager.

E 04:39:21 Visit http://www.imgburn.com to download one.

E 04:39:21 Alternatively, try changing the 'I/O Interface' in the Settings to a different one.

Link to comment
Share on other sites

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.