Miscompare Error verifing write

[kprobus]

I'm using an LG DVD writer with Memorx x16 and after writing a DVD I get this error: Miscompare at LBA: 316, Offset: 49, File: VIDEO_TS\VIDEO_TS.VOB

Here is the log:

I 08:36:36 ImgBurn Version 2.1.0.0 started!

I 08:36:36 Microsoft Windows XP Professional (5.1, Build 2600 : Service Pack 2)

W 08:36:36 Drive D:\ (FAT32) does not support single files > 4 GB

I 08:36:36 Initialising SPTI...

I 08:36:36 Searching for SCSI / ATAPI devices...

I 08:36:36 Found 1 DVD?RW/RAM!

I 08:37:46 Operation Started!

I 08:37:46 Source File: C:\Documents and Settings\Ken\Desktop\DVD\THEILLUSIONIST_D2.ISO

I 08:37:46 Source File Sectors: 2,285,874 (MODE1/2048)

I 08:37:46 Source File Size: 4,681,469,952 bytes

I 08:37:46 Source File Volume Identifier: THEILLUSIONIST_D2

I 08:37:46 Source File Implementation Identifier: DVD Shrink

I 08:37:46 Source File File System(s): ISO9660, UDF (1.02)

I 08:37:46 Destination Device: [1:0:0] HL-DT-ST DVDRAM GSA-H10L LL10 (E:) (ATA)

I 08:37:46 Destination Media Type: DVD+R (Disc ID: CMC MAG-M01-00) (Speeds: 4x, 8x, 12x, 16x)

I 08:37:46 Destination Media Sectors: 2,295,104

I 08:37:46 Write Mode: DVD

I 08:37:46 Write Type: DAO

I 08:37:46 Write Speed: MAX

I 08:37:46 Link Size: Auto

I 08:37:46 Test Mode: No

I 08:37:46 BURN-Proof: Enabled

I 08:37:46 Filling Buffer...

I 08:37:47 Writing LeadIn...

I 08:38:17 Writing Image...

I 09:15:31 Synchronising Cache...

I 09:15:32 Closing Track...

I 09:15:36 Finalising Disc...

I 09:15:53 Image MD5: 26bcd52aa13fcb15d0d224d26360c198

I 09:15:53 Operation Successfully Completed! - Duration: 00:38:06

I 09:15:53 Average Write Rate: 2,047 KB/s (1.5x) - Maximum Write Rate: 2,555 KB/s (1.8x)

I 09:15:53 Cycling Tray before Verify...

W 09:16:03 Waiting for device to become ready...

I 09:16:18 Device Ready!

I 09:16:18 Operation Started!

I 09:16:18 Source Device: [1:0:0] HL-DT-ST DVDRAM GSA-H10L LL10 (E:) (ATA)

I 09:16:18 Source Media Type: DVD+R (Book Type: DVD+R) (Disc ID: CMC MAG-M01-00) (Speeds: 4x, 8x, 12x, 16x)

I 09:16:18 Image File: C:\Documents and Settings\Ken\Desktop\DVD\THEILLUSIONIST_D2.ISO

I 09:16:18 Image File Sectors: 2,285,874 (MODE1/2048)

I 09:16:18 Image File Size: 4,681,469,952 bytes

I 09:16:18 Image File Volume Identifier: THEILLUSIONIST_D2

I 09:16:18 Image File Implementation Identifier: DVD Shrink

I 09:16:18 Image File File System(s): ISO9660, UDF (1.02)

I 09:16:18 Verifying Sectors...

W 09:16:28 Miscompare at LBA: 316, Offset: 49, File: VIDEO_TS\VIDEO_TS.VOB

W 09:16:28 Device: 0x00

W 09:16:28 Image File: 0x80

W 09:16:28 Total Errors in Sector: 1

I 09:16:28 Verifying Sectors...

Does Imgburn support LG DVD writers?

[kevdriver]

Its not a matter or Imgburn supporting your writer, it supports all writers. Its a matter of your writer be able to burn successfully to blank media.

 

 

DVD+R (Disc ID: CMC MAG-M01-00) (Speeds: 4x, 8x, 12x, 16x)

These discs are absolute garbage. We reccommend Verbatim or Taio Yudens for successful burns. -R for SL burning and +R for dual layer burning.

 

You may also like to check your firmware out www.rpc1.org The most current is LL11

[lfcrule1972]

Also take a look at the FAQs section and the part about your DMA. From your log it shows that the media (crap as it is) supports writing up to 16x, the settings on ImgBurn show you have Max speed selected yet your burn was as follows:

 

I 09:15:53 Operation Successfully Completed! - Duration: 00:38:06

I 09:15:53 Average Write Rate: 2,047 KB/s (1.5x) - Maximum Write Rate: 2,555 KB/s (1.8x)

This to me points to a DMA issue as well - follow the FAQ guide (even if DMA says it's enabled, Windows falsely reports this) and hopefully you can increase your burn speeds