Jump to content

Problem in playing ImgBurn'ed movie on DVD Player.


CdSlc

Recommended Posts

I have this movie on a DVD+R disk, that I am trying to make a backup of, into a DVD-R disk using ImgBurn. The source disk works fine on my laptop as well as my DVD player. The backup disk works fine on my laptop, but does not work on my DVD player. When I say does not work, the symptoms are various, like:

- There are those rainbow colored bands going across the screen at various places.

- Sometimes the audio gets cut off.

- Sometimes the audio is not in sync with the video.

- Sometimes the video just freezes up, after playing for 5-10 minutes.

- Sometimes the DVD player is stuck at the initial "Loading" screen itself.

- Sometimes if I skip the inital 15-20 minutes of bad recording, then everything seems to be working fine.

 

I still haven't got a singe DVD disk that plays flawlessly on my DVD player, from begin to end. All, I have to show for my effort is a bunch of coasters.

 

My laptop is a brand-new Everex VA4103M running Windows vista Home Basic. My DVD player is a Cyberhome CH-DVD 300 player. This is the very first time that I burning DVD disk on the laptop. I like the Cyberhome DVD player, since this is one of the very few that I have found, which can play anything that you throw at it. Except, now I find, that it cannot play the DVD disk that I am burning.

 

There is no encryption on the source disk. I can make a backup copy of the same source disk using Nero (trial version) and this plays fine on the DVD player. Rather than paying $70 to get Nero, I would prefer to use ImgBurn.

 

During my Google search, I read that if the audio and video is not in sync, then burn the DVD at the lowest possible speed, and that is what I have done. In one of the ImgBurn screen, it showed that the lowest speed for my media is 2.4x and so I have been consistently burning the DVDs at 2.4x.

 

I have gone through all the guides listed in the "ImgBurn Support Forum > General > Guides" forum. I have gone through all guides that I could find on videhelp.com. Burned using those guide and I have created some more coasters.

 

From my source disk, I created an ISO image as well as a backup of the whole disk (including the AUDIO_TS and VIDEO_TS folders) onto my hard disk. This was done just to eliminate any problem that could happen with buffering, etc. from the laptop's DVD drive. Using both the ISO image and VIDEO_TS folder, I have tried various ways of burning the movie, but none of them seem to be working.

 

I tried burning the same movie on a different DVD+R disk, the result is still the same.

 

I tried burning a different movie on the DVD-R disk, the result is still the same. I don't have any other DVD burners available, unless I go and buy a new external DVD burner.

 

I searched in this forum and I found that the DVD media that is recommended is either Verbatim or Taiyo Yuden. So, other than getting those media, is there anything that I can do with my existing media to resolve this problem?

 

Below is the ImgBurn log file from my latest burning adventure:

 

*****************************************************************

 

I 14:32:07 ImgBurn Version 2.3.0.0 started!

I 14:32:07 Microsoft Windows Vista Home Basic Edition (6.0, Build 6000)

I 14:32:07 Total Physical Memory: 456,576 KB - Available: 128,720 KB

I 14:32:07 Initialising SPTI...

I 14:32:07 Searching for SCSI / ATAPI devices...

I 14:32:07 Found 1 DVD?RW!

I 14:35:39 Operation Started!

I 14:35:39 Building Image Tree...

I 14:35:39 Checking Directory Depth...

I 14:35:39 Calculating Totals...

I 14:35:39 Preparing Image...

I 14:35:40 Checking Path Length...

I 14:35:40 Image Size: 4,656,267,264 bytes

I 14:35:40 Image Sectors: 2,273,568

I 14:35:40 Operation Successfully Completed! - Duration: 00:00:00

I 14:36:54 Operation Started!

I 14:36:54 Building Image Tree...

I 14:36:54 Checking Directory Depth...

I 14:36:54 Calculating Totals...

I 14:36:54 Preparing Image...

I 14:36:55 Checking Path Length...

I 14:36:55 Image Size: 4,656,267,264 bytes

I 14:36:55 Image Sectors: 2,273,568

I 14:37:00 Operation Successfully Completed! - Duration: 00:00:05

I 14:37:00 Operation Started!

I 14:37:00 Source File: -==/\/[bUILD IMAGE]\/\==-

I 14:37:00 Source File Sectors: 2,273,568 (MODE1/2048)

I 14:37:00 Source File Size: 4,656,267,264 bytes

I 14:37:00 Source File Volume Identifier: Vivah

I 14:37:00 Source File Application Identifier: IMGBURN V2.3.0.0 - THE ULTIMATE IMAGE BURNER!

I 14:37:00 Source File Implementation Identifier: ImgBurn

I 14:37:00 Source File File System(s): ISO9660, UDF (1.02)

I 14:37:00 Destination Device: [3:0:0] Optiarc DVD RW AD-5530A AX24 (E:) (ATA)

I 14:37:00 Destination Media Type: DVD+R (Disc ID: MCC-004-00) (Speeds: 2.4x, 4x, 6x, 8x)

I 14:37:00 Destination Media Sectors: 2,295,104

I 14:37:00 Write Mode: DVD

I 14:37:00 Write Type: DAO

I 14:37:00 Write Speed: 2.4x

I 14:37:00 Link Size: Auto

I 14:37:00 Test Mode: No

I 14:37:00 BURN-Proof: Enabled

I 14:37:05 Filling Buffer... (20 MB)

I 14:37:07 Writing LeadIn...

I 14:37:23 Writing Image... (LBA: 0 - 2273567)

I 15:01:35 Synchronising Cache...

I 15:01:46 Closing Track...

I 15:01:48 Finalising Disc...

I 15:02:35 Image MD5: 8d2c1babdded67fc90ab33aa0f328111

I 15:02:36 Operation Successfully Completed! - Duration: 00:25:35

I 15:02:36 Average Write Rate: 3,131 KB/s (2.3x) - Maximum Write Rate: 3,375 KB/s (2.4x)

I 15:02:36 Cycling Tray before Verify...

W 15:02:41 Waiting for device to become ready...

I 15:04:29 Device Ready!

I 15:04:29 Operation Started!

I 15:04:29 Source Device: [3:0:0] Optiarc DVD RW AD-5530A AX24 (E:) (ATA)

I 15:04:29 Source Media Type: DVD+R (Book Type: DVD-ROM) (Disc ID: MCC-004-00) (Speeds: 2.4x, 4x, 6x, 8x)

I 15:04:29 Image File: -==/\/[bUILD IMAGE]\/\==-

I 15:04:29 Image File Sectors: 2,273,568 (MODE1/2048)

I 15:04:29 Image File Size: 4,656,267,264 bytes

I 15:04:29 Image File Volume Identifier: Vivah

I 15:04:29 Image File Application Identifier: IMGBURN V2.3.0.0 - THE ULTIMATE IMAGE BURNER!

I 15:04:29 Image File Implementation Identifier: ImgBurn

I 15:04:29 Image File File System(s): ISO9660, UDF (1.02)

I 15:04:30 Verifying Sectors... (LBA: 0 - 2273567)

I 15:13:53 Device MD5: 8d2c1babdded67fc90ab33aa0f328111

I 15:13:53 Image MD5: 8d2c1babdded67fc90ab33aa0f328111

I 15:13:53 Operation Successfully Completed! - Duration: 00:09:23

I 15:13:53 Average Verify Rate: 8,076 KB/s (5.8x) - Maximum Verify Rate: 11,722 KB/s (8.5x)

 

*****************************************************************

 

Thanks.

Link to comment
Share on other sites

clean the lens on home dvd player, set booktype to dvd-rom(got a feeling that drive will not allow this without hacking he firmware)

 

get some good quality dvd-r and try buy another home dvd player and get a yamada or Umax also try and get one that plays [mpeg 4/ divx/xvid and has hdmi] everything i put in brackets would be optional and only suggested so as not to have to replace your dvd player again within 2 years.

 

 

 

You would have to be certain that the source files are good.

Link to comment
Share on other sites

It's already booktyping to DVD-ROM:

I 15:04:29 Source Media Type: DVD+R (Book Type: DVD-ROM) (Disc ID: MCC-004-00) (Speeds: 2.4x, 4x, 6x, 8x)

 

Taiyo Yuden and/or Verbatim media may help, but I think the problem is your DVD player. I've had the Cyberhome CH-DVD 300 and mine barely played pressed DVDs, didn't play DVD?R and didn't even recognize CD-RWs/DVD?RWs. At the time I had bought 2 brand new units and they both had the same problems. I've returned them and bought a Philips DVP642K (which is old now) and this one plays any media you throw at it, plus it has support for DivX/XviD.

Link to comment
Share on other sites

im sure i seen the answer to this already but i cant find it. so, i just wrote my movie file VIDEO_TS to a DVD-R. It won't play on my laptop DVD player like normal. What did I do wrong?

 

I 17:43:37 ImgBurn Version 2.3.0.0 started!

I 17:43:37 Microsoft Windows XP Professional (5.1, Build 2600 : Service Pack 2)

I 17:43:37 Total Physical Memory: 514,480 KB - Available: 218,724 KB

I 17:43:37 Initialising SPTI...

I 17:43:37 Searching for SCSI / ATAPI devices...

I 17:43:47 Found 1 DVD-ROM/CD-RW and 1 DVD?RW!

I 17:44:13 Operation Started!

I 17:44:13 Source File: C:\KING_KONG\VIDEO_TS\King Kong DVD.iso

I 17:44:13 Source File Sectors: 608 (MODE1/2048)

I 17:44:13 Source File Size: 1,245,184 bytes

I 17:44:13 Source File Volume Identifier: KING_KONG

I 17:44:13 Source File Application Identifier: IMGBURN V2.3.0.0 - THE ULTIMATE IMAGE BURNER!

I 17:44:13 Source File Implementation Identifier: ImgBurn

I 17:44:13 Source File File System(s): ISO9660, UDF (1.02)

I 17:44:13 Destination Device: [0:0:0] DVDRW DRW-6S160P PSG6 (G:) (USB)

I 17:44:13 Destination Media Type: DVD-R (Disc ID: CMC MAG. AM3) (Speeds: 6x, 8x, 12x, 16x)

I 17:44:13 Destination Media Sectors: 2,297,888

I 17:44:13 Write Mode: DVD

I 17:44:13 Write Type: DAO

I 17:44:13 Write Speed: MAX

I 17:44:13 Link Size: Auto

I 17:44:13 Test Mode: No

I 17:44:13 BURN-Proof: Enabled

I 17:44:13 Filling Buffer... (20 MB)

I 17:44:13 Writing LeadIn...

I 17:45:19 Writing Image... (LBA: 0 - 607)

I 17:45:19 Synchronising Cache...

I 17:47:03 Image MD5: 1fb4b43763de8c5e84266fa269b37703

I 17:47:03 Operation Successfully Completed! - Duration: 00:02:50

I 17:47:03 Average Write Rate: N/A - Maximum Write Rate: N/A

I 17:47:03 Cycling Tray before Verify...

W 17:47:13 Waiting for device to become ready...

I 17:47:25 Device Ready!

I 17:47:25 Operation Started!

I 17:47:25 Source Device: [0:0:0] DVDRW DRW-6S160P PSG6 (G:) (USB)

I 17:47:25 Source Media Type: DVD-R (Book Type: DVD-R) (Disc ID: CMC MAG. AM3) (Speeds: 6x, 8x, 12x, 16x)

I 17:47:25 Image File: C:\KING_KONG\VIDEO_TS\King Kong DVD.iso

I 17:47:25 Image File Sectors: 608 (MODE1/2048)

I 17:47:25 Image File Size: 1,245,184 bytes

I 17:47:25 Image File Volume Identifier: KING_KONG

I 17:47:25 Image File Application Identifier: IMGBURN V2.3.0.0 - THE ULTIMATE IMAGE BURNER!

I 17:47:25 Image File Implementation Identifier: ImgBurn

I 17:47:25 Image File File System(s): ISO9660, UDF (1.02)

I 17:47:25 Verifying Sectors... (LBA: 0 - 607)

I 17:47:28 Device MD5: 1fb4b43763de8c5e84266fa269b37703

I 17:47:28 Image MD5: 1fb4b43763de8c5e84266fa269b37703

I 17:47:29 Operation Successfully Completed! - Duration: 00:00:03

I 17:47:29 Average Verify Rate: 405 KB/s (0.3x) - Maximum Verify Rate: 405 KB/s (0.3x)

I 17:53:34 Operation Started!

I 17:53:34 Device: [0:0:0] DVDRW DRW-6S160P PSG6 (G:) (USB)

I 17:53:34 Media Type: DVD-RW (Disc ID: CMC MAG. AM3) (Speeds: 6x, 8x, 12x, 16x)

I 17:53:34 Quick Erase: Yes

I 17:53:34 Erasing Disc...

E 17:53:37 Operation Failed! - Duration: 00:00:03

Link to comment
Share on other sites

Cross posting, hijacking some other thread is not a good net-iquette.

 

Anyways, thanks everybody for all the suggestions. For some odd reason, I never considered the idea that DVD player could be the culprit.

 

So yesterday, I again burned the movie on a DVD-R disk, tried playing it in the Cyberhome DVD player, it did not work. So I took the same DVD disk to a different DVD player, its one of those Magnavox TV-DVD combo thingy. The DVD disk works great in this combo DVD player, no skipping, no rainbow bands across the screen, etc.

 

So, I guess the Cyberhome DVD player is the culprit. Their manual says that it can play both DVD-R and DVD+R disk. My source disk is a DVD+R disk, and Cyberhome is able to play it fine. For some reason, its not able to play the DVD-R disk. Before totally giving up on the Cyberhome DVD player, I might try getting some other brand DVD-R and DVD+R disk, and give it a try.

 

Thanks for all the help. At least, now I know where I should concentrate my effort on. I have been wasting all my energy trying to burn so many DVD disk, using different settings, different software, etc. under the assumption that there is something wrong with the burning process.

Link to comment
Share on other sites

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.