Jump to content


  • Content Count

  • Joined

  • Last visited

About itm

  • Rank
    ISF Newbie
  1. To summarise...I was trying to write 4 files (large .exe files) to a 7GB DVD-R, from a half empty tub that I hadn't used for a few years. The first couple of burns failed, at which point I suspected that maybe the media had degraded while sat on the shelf (I had noticed some moisture on the discs which I needed to wipe off - I suspect this dated back to a leak in my study over a year ago). When the third burn failed I decided that I should try an alternative media, in case there was in fact a problem with the drive or software. So I tried burning the same files to a 4GB DVD-RW (forgetting that it had half the capacity of the DVD-R's). When I got the warning message about the capacity I tried again, but only burning two of the four files, so that they would fit on the disc. I got the same error that I had with the DVD-R's. At that point I posted my message here.
  2. Sorry I think I must have uploaded the wrong section of the log. On one of my attempts to burn to the DVR I burned only a couple of the files, so that it would all fit onto the disc, but got that same error.
  3. OK so I followed dbminter's instructions to update the drive firmware, then rebooted. After the reboot everything was fine -thanks! I've been using the same DV-R/W media for 5+ years without any problems (am actually using discs from the same pack that I bought 5 years ago), so it didn't seem like a media compatibility issue. ???
  4. This was the last entry from the log: I 18:30:40 Operation Started! I 18:30:40 Building Image Tree... I 18:30:46 Calculating Totals... I 18:30:46 Preparing Image... I 18:30:46 Contents: 4 Files, 1 Folder I 18:30:46 Content Type: Data I 18:30:46 Data Type: MODE1/2048 I 18:30:46 File System(s): UDF (1.02) I 18:30:46 Volume Label: Realtracks & Realdrums5 I 18:30:46 Size: 6,556,174,779 bytes I 18:30:46 Sectors: 3,201,259 I 18:30:46 Image Size: 6,556,745,728 bytes I 18:30:46 Image Sectors: 3,201,536 I 18:30:47 Operation Successfully Completed! - Duration: 00:00:07 W 18:30:49 User accepted disc space warning and is attempting to overburn! I 18:30:49 Operation Started! I 18:30:49 Source File: -==/\/[BUILD IMAGE]\/\==- I 18:30:49 Source File Sectors: 3,201,536 (MODE1/2048) I 18:30:49 Source File Size: 6,556,745,728 bytes I 18:30:49 Source File Volume Identifier: Realtracks & Realdrums5 I 18:30:49 Source File Volume Set Identifier: 509E93D40030D9F6 I 18:30:49 Source File Application Identifier: ImgBurn v2.5.8.0 I 18:30:49 Source File Implementation Identifier: ImgBurn I 18:30:49 Source File File System(s): UDF (1.02) I 18:30:49 Destination Device: [0:0:0] HL-DT-ST BD-RE BH10LS30 1.00 (E:) (SATA) I 18:30:49 Destination Media Type: DVD-RW (Disc ID: TDK502sakuM3) I 18:30:49 Destination Media Supported Write Speeds: 2x I 18:30:49 Destination Media Sectors: 2,298,496 I 18:30:49 Write Mode: DVD I 18:30:49 Write Type: DAO I 18:30:49 Write Speed: MAX I 18:30:49 Link Size: Auto I 18:30:49 Lock Volume: Yes I 18:30:49 Test Mode: No I 18:30:49 OPC: No I 18:30:49 BURN-Proof: Enabled I 18:30:49 Write Speed Successfully Set! - Effective: 2,770 KB/s (2x) E 18:31:00 Failed to Reserve Track! - Reason: Invalid Field in CDB E 18:31:02 Operation Failed! - Duration: 00:00:12 I 18:31:02 Average Write Rate: N/A - Maximum Write Rate: N/A I 18:31:25 Close Request Acknowledged I 18:31:25 Closing Down... I 18:31:26 Shutting down SPTI... I 18:31:26 ImgBurn closed!
  5. I am using ImgBurn on Windows 10, attempting to burn 4 .exe files in a folder to a 7GB DVD-R. A number of attempts have now failed with the error below. The files vary in size from 1.5GB to 1.9GB. Any idea why I am getting this error? I/O Error! Device: [0:0:0] HL-DT-ST BD-RE BH10LS30 1.00 (E:) (SATA) ScsiStatus: 0x02 Interpretation: Check Condition CDB: 53 00 00 00 00 00 30 DA 00 00 Interpretation: Reserve Track - Sectors: 3,201,536 Sense Area: 70 00 05 00 00 00 00 0A 53 00 00 0D 24 00 00 C0 00 05 SK Interpretation: Illegal Request ASC/ASCQ Interpretation: Invalid Field in CDB
  6. Please ignore this - the disc burn actually seems to have completed!
  7. I was burning a 25GB BD-R using Imgburn 2.5.80 (on Windows 10 Pro). I accidentally happened upon a keystroke which seems to have paused the disc burning process. The progress window has gone, the BD-RW drive is no longer being accessed, and the green bar at the bottom of the Disk Layout Editor has a white highlight scrolling across it repeatedly. To the right of the green bar it says 99% (I suspect that is the % full figure for the disc, rather than the progress of the burn?). Can anyone advise on how I can resume and complete the burning process?

Important Information

By using this site, you agree to our Terms of Use.