Jump to content

Power Calibration Area Error (1 of 20)


nguyenkzz

Recommended Posts

This is my problem

 

I 20:14:19 ImgBurn Version 2.5.5.0 started!

I 20:14:19 Microsoft Windows XP Professional (5.1, Build 2600 : Service Pack 3)

I 20:14:19 Total Physical Memory: 506,604 KB - Available: 256,884 KB

I 20:14:20 Initialising SPTI...

I 20:14:20 Searching for SCSI / ATAPI devices...

I 20:14:20 -> Drive 1 - Info: ASUS DRW-1814BL 1.10 (G:) (ATA)

I 20:14:20 -> Drive 2 - Info: ASUS DVD-E616A 1.03 (F:) (ATA)

I 20:14:20 Found 1 DVD-ROM and 1 DVD±RW/RAM!

I 20:15:07 Operation Started!

...

 

I 20:15:28 Destination Device: [3:1:0] ASUS DRW-1814BL 1.10 (G:) (ATA)

I 20:15:28 Destination Media Type: DVD-R (Disc ID: CMC MAG. AM3) (Speeds: 4x, 8x, 10x, 12x, 16x)

I 20:15:28 Destination Media Sectors: 2,297,888

I 20:15:28 Write Mode: DVD

I 20:15:28 Write Type: DAO

I 20:15:28 Write Speed: 12x

I 20:15:28 Link Size: Auto

I 20:15:28 Lock Volume: Yes

I 20:15:28 Test Mode: No

I 20:15:28 OPC: No

I 20:15:28 BURN-Proof: Enabled

I 20:15:28 Write Speed Successfully Set! - Effective: 16,620 KB/s (12x)

I 20:15:28 Filling Buffer... (20 MB)

I 20:15:29 Writing LeadIn...

W 20:15:53 Failed to Write Sectors 0 - 31 - Reason: Power Calibration Area Error

W 20:15:53 Retrying (1 of 20)...

I 20:15:53 Writing LeadIn...

I 20:16:12 Writing Session 1 of 1... (1 Track, LBA: 0 - 2253135)

I 20:16:12 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 2253135)

I 20:23:48 Synchronising Cache...

I 20:24:02 Exporting Graph Data...

I 20:24:02 Graph Data File: C:\Documents and Settings\Administrator\Application Data\ImgBurn\Graph Data Files\ASUS_DRW-1814BL_1.10_MONDAY-JUNE-27-2011_8-15_PM_CMC_MAG._AM3_12x.ibg

I 20:24:02 Export Successfully Completed!

I 20:24:02 Operation Successfully Completed! - Duration: 00:08:34

I 20:24:02 Average Write Rate: 9,882 KB/s (7.1x) - Maximum Write Rate: 16,804 KB/s (12.1x)

I 20:24:02 Cycling Tray before Verify...

W 20:24:09 Waiting for device to become ready...

I 20:25:03 Device Ready!

E 20:25:03 CompareImageFileLayouts Failed! - Session Count Not Equal (1/0)

E 20:25:03 Verify Failed! - Reason: Layouts do not match.

 

There was an error, but it was still writing disc. Afterall, program informs "Operation Successfully Completed!" but the disc can not be opened at all :|

 

Can you give me an explanation?

Thanks a lot

Edited by nguyenkzz
Link to comment
Share on other sites

I 20:15:28 Destination Device: [3:1:0] ASUS DRW-1814BL 1.10 (G:) (ATA)

I 20:15:28 Destination Media Type: DVD-R (Disc ID: CMC MAG. AM3) (Speeds: 4x, 8x, 10x, 12x, 16x)

I 20:15:28 Write Speed: 12x

Your burner doesn't like the media you're using. Update your burner's firmware (remove any disc from the drive and close the tray then run the firmware updater) and try burning again. You could also try burning at 8x.

Link to comment
Share on other sites

I 20:15:28 Destination Device: [3:1:0] ASUS DRW-1814BL 1.10 (G:) (ATA)

I 20:15:28 Destination Media Type: DVD-R (Disc ID: CMC MAG. AM3) (Speeds: 4x, 8x, 10x, 12x, 16x)

I 20:15:28 Write Speed: 12x

Your burner doesn't like the media you're using. Update your burner's firmware (remove any disc from the drive and close the tray then run the firmware updater) and try burning again. You could also try burning at 8x.

 

the second time in-a-row i burn it, it works 100%

I think it must be the burner. Recently it has not worked properly

 

Anyway, i'll try the firmware :D

This error happens unpredictably, not all the time.

Link to comment
Share on other sites

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.