JeffDaniels
-
Posts
5 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Posts posted by JeffDaniels
-
-
Sooo, i posted the other day about an error I was receiving regarding no sense information or something of that nature. I tried everything under the sun and determined that after changing pcs, and moving the drive it must have gone bad because nothing worked. (it worked fine in my old pc)
So now, i purchased a new drive, and it started off great, made it all the way to 100% and then failed "because of an i/o device error" when trying to finalize the disc.
This is driving me nuts, because i love imgburn and never had a problem with it in the past. Some information you may or may not need, it's a new dell xps 420 (well not new to the market but new to me) and only supports sata connections not ide. But of course when i bought the new burner it didn't say sata and i just assumed it would be since it appeared to be a newer drive released later than my previous. Anyway it is also ide, so i currently have it set up connecting to a sata controller card attached to my pci slot. As i said, it runs all the way through but won't finalize the disc. Any suggestions? Thoughts? Please help...thanks guys.
Here is the log...
21:27:55 ImgBurn Version 2.4.2.0 started!
I 21:27:55 Microsoft Windows Vista Home Premium Edition (6.0, Build 6000)
I 21:27:55 Total Physical Memory: 3,142,988 KB - Available: 2,089,204 KB
I 21:27:55 Initialising SPTI...
I 21:27:55 Searching for SCSI / ATAPI devices...
I 21:27:56 Found 1 DVD
-
on the back of drive there is a little jumper it might already be on master but if not move it to there.
might also be a newer firmware for your drive
oh ok, always heard of it as just a jumper not a pio...and yea i had that set to master.
Looks like i'm just screwed again. Alright, thanks again for your help.
-
Try different usb port then get a different usb external/converter, set pio to master and check short/ide cable.
Thank u for the quick reply...so i did try a different usb port before i posted, but not to sound ignorant but how do i set pio to master? Do i need to go into the bios?
-
Soooo, I had a pioneer 111d in my old pc, worked lovely, imgburn ran smooth as smooth can be. Then I got a new computer, with only sata hookups (the dell xps420) and all hell broke loose.
I have tried a few different connections, first i had a sata controller card i was hooked up to, which started the burn and then failed a few minutes in. So i decided to get an ide to usb connector. Soooo I hooked it all up, and it recognizes the drive just fine...
But when i go to burn with imgburn it tries to set the l0 data zone capacity for 1 min and 30 seconds, with no results, and then i get the "failed to set l0 data zone capacity reason: no additional sense information" error. I tried searching through here but couldn't understand what might be causing this. Any help would be greatly appreciated? This is driving me nuts, and I am using Verbatim discs. Here is my log...thanks in advance for any feedback
//****************************************\\
; ImgBurn Version 2.4.2.0 - Log
; Friday, 22 August 2008, 17:53:35
; \\****************************************//
;
;
I 17:47:05 ImgBurn Version 2.4.2.0 started!
I 17:47:05 Microsoft Windows Vista Home Premium Edition (6.0, Build 6000)
I 17:47:05 Total Physical Memory: 3,142,988 KB - Available: 2,214,472 KB
I 17:47:05 Initialising SPTI...
I 17:47:05 Searching for SCSI / ATAPI devices...
I 17:47:05 Found 2 DVD
Ok, Soooo i've got a new question
in ImgBurn Support
Posted
Thanks mmalves, also i've seen a lot of your posts and have to ask...any idea who the girl is in your avatar? Lol...thanx.