pjcamp
-
Posts
9 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Posts posted by pjcamp
-
-
But it IS blank. It is retaining the info from the previous burn after the burned disc has been replaced with a blank one.
-
It is reporting this:
HL-DT-ST BD-RE WH10LS30 1.02 (ATA)
Current Profile: DVD+R DL
Disc Information:
Status: Complete
State of Last Session: Complete
Erasable: No
Sessions: 1
Sectors: 3,979,296
Size: 8,149,598,208 bytes
Time: 884:19:21 (MM:SS:FF)
MID: MKM-003-00
Supported Write Speeds: 4x, 8x
DVD±R DL Boundary Information:
L0 Data Zone Capacity: 1,989,648
Changeable: No
TOC Information:
Session 1... (LBA: 0)
-> Track 01 (Mode 1, LBA: 0 - 3979295)
-> LeadOut (LBA: 3979296)
Disc Control Blocks Information:
WH10LS30
Physical Format Information (Last Recorded - L0):
Disc ID: MKM-003-00
Book Type: DVD-ROM
Part Version: 1
Disc Size: 120 mm
Maximum Read Rate: Not Specified
Number of Layers: 2
Track Path: Opposite Track Path (OTP)
Linear Density: 0.293 um/bit
Track Density: 0.74 um/track
First Physical Sector of Data Area: 196,608
Last Physical Sector of Data Area: 16,580,607
Last Physical Sector in Layer 0: 2,186,255
Physical Format Information (Last Recorded - L1):
Disc ID: MKM-003-00
Book Type: DVD-ROM
Part Version: 1
Disc Size: 120 mm
Maximum Read Rate: Not Specified
Number of Layers: 2
Track Path: Opposite Track Path (OTP)
Linear Density: 0.293 um/bit
Track Density: 0.74 um/track
First Physical Sector of Data Area: 196,608
Last Physical Sector of Data Area: 16,580,607
Last Physical Sector in Layer 0: 2,186,255
Layer Information:
Layer 0 Sectors: 1,989,648 (50%)
Layer 1 Sectors: 1,989,648 (50%)
Performance (Write Speed):
Descriptor 1...
-> B0: 0x02, B1: 0x00, B2: 0x00, B3: 0x00
-> EL: 3979295 (0x003CB81F)
-> RS: 10,863 KB/s (8x) - WS: 5,540 KB/s (4x)
Descriptor 2...
-> B0: 0x02, B1: 0x00, B2: 0x00, B3: 0x00
-> EL: 3979295 (0x003CB81F)
-> RS: 10,863 KB/s (8x) - WS: 11,080 KB/s (8x)
-
OK, now, it baffles me why when I put a blank disc in Imgburn claims it is not empty until I close and restart Imgburn.
-
I've tried 8x. I dialed it down to 4x just to see if that helped. I have to find my cleaning disc and then I'll try that.
I think your guess is probably right. After a few times I noticed the error message came up immediately after the tray cycle between write and verify.
-
Addendum: Afterwards, it does not recognize that a disc has been ejected or a new one loaded.
-
As near as I can tell the burn succeeded. I can play the resulting DVD and see all the files on it.
Interestingly, this problem started simultaneously with an upgrade from Windows 7 to Windows 10. I'd suspect a driver problem but Windows reports it is the latest driver. I'd suspect a firmware problem but it has the latest firmware (I flashed it again just in case of corruption). I'm using single layer Taiyo-Yuden disks, and burned over half of a 100 disk spindle flawlessly before the upgrade.
I'm more than a little baffled, and don't know whether to trust ImgBurn at the moment.
Log follows.
I 20:56:03 ImgBurn Version 2.5.8.0 started!
I 20:56:03 Microsoft Windows 8 Professional x64 Edition (6.2, Build 9200)
I 20:56:03 Total Physical Memory: 16,706,220 KiB - Available: 13,499,564 KiB
W 20:56:03 Duplex Secure's SPTD driver can have a detrimental effect on drive performance.
I 20:56:03 Initialising SPTI...
I 20:56:03 Searching for SCSI / ATAPI devices...
I 20:56:03 -> Drive 1 - Info: HL-DT-ST DVDRAM GSA-H62N CL01-T0 (F:) (ATA)
I 20:56:03 -> Drive 2 - Info: HL-DT-ST BD-RE WH10LS30 1.02-A0 (G:) (ATA)
I 20:56:03 Found 1 DVD±RW/RAM and 1 BD-RE!
I 20:56:49 Operation Started!
I 20:56:49 Building Image Tree...
I 20:56:51 Checking Directory Depth...
I 20:56:51 Calculating Totals...
I 20:56:51 Preparing Image...
I 20:56:51 Checking Path Length...
I 20:56:51 Contents: 13 Files, 2 Folders
I 20:56:51 Content Type: DVD Video
I 20:56:51 Data Type: MODE1/2048
I 20:56:51 File System(s): ISO9660, UDF (1.02)
I 20:56:51 Volume Label: UNDEFINED
I 20:56:51 IFO/BUP 32K Padding: Enabled
I 20:56:51 Region Code: 1, 2, 3, 4, 5, 6, 7, 8
I 20:56:51 TV System: NTSC
I 20:56:51 Size: 2,552,559,616 bytes
I 20:56:51 Sectors: 1,246,367
I 20:56:51 Image Size: 2,553,151,488 bytes
I 20:56:51 Image Sectors: 1,246,656
I 20:56:53 Operation Successfully Completed! - Duration: 00:00:03
I 20:56:53 Operation Started!
I 20:56:53 Source File: -==/\/[bUILD IMAGE]\/\==-
I 20:56:53 Source File Sectors: 1,246,656 (MODE1/2048)
I 20:56:53 Source File Size: 2,553,151,488 bytes
I 20:56:53 Source File Volume Identifier: UNDEFINED
I 20:56:53 Source File Volume Set Identifier: 482CA718001305BA
I 20:56:53 Source File Application Identifier: IMGBURN V2.5.8.0 - THE ULTIMATE IMAGE BURNER!
I 20:56:53 Source File Implementation Identifier: ImgBurn
I 20:56:53 Source File File System(s): ISO9660, UDF (1.02)
I 20:56:53 Destination Device: [3:15:0] HL-DT-ST BD-RE WH10LS30 1.02 (G:) (ATA)
I 20:56:53 Destination Media Type: DVD+R (Disc ID: YUDEN000-T02-00)
I 20:56:53 Destination Media Supported Write Speeds: 4x, 8x
I 20:56:53 Destination Media Sectors: 2,295,104
I 20:56:53 Write Mode: DVD
I 20:56:53 Write Type: DAO
I 20:56:53 Write Speed: 4x
I 20:56:53 DVD+R Reserve Track: No
I 20:56:53 Link Size: Auto
I 20:56:53 Lock Volume: Yes
I 20:56:53 Test Mode: No
I 20:56:53 OPC: No
I 20:56:53 BURN-Proof: Enabled
I 20:56:53 Write Speed Successfully Set! - Effective: 5,540 KB/s (4x)
I 20:56:53 Book Type Setting: DVD-ROM
I 20:56:53 Filling Buffer... (80 MiB)
I 20:56:54 Writing LeadIn...
I 20:57:10 Writing Session 1 of 1... (1 Track, LBA: 0 - 1246655)
I 20:57:10 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 1246655)
I 21:04:56 Synchronising Cache...
I 21:04:57 Closing Track...
I 21:04:59 Finalising Disc...
I 21:05:42 Exporting Graph Data...
I 21:05:42 Graph Data File: C:\Users\pjcamp\AppData\Roaming\ImgBurn\Graph Data Files\HL-DT-ST_BD-RE_WH10LS30_1.02_TUESDAY-JANUARY-12-2016_8-56_PM_YUDEN000-T02-00_4x.ibg
I 21:05:42 Export Successfully Completed!
I 21:05:42 Operation Successfully Completed! - Duration: 00:08:49
I 21:05:42 Average Write Rate: 5,361 KiB/s (4.0x) - Maximum Write Rate: 5,461 KiB/s (4.0x)
I 21:05:42 Cycling Tray before Verify...
I 21:05:50 Device Ready!
E 21:05:50 CompareImageFileLayouts Failed! - Session Count Not Equal (1/0)
E 21:05:50 Verify Failed! - Reason: Layouts do not match.
-
Firmware update did it. Now it verifies around 10x. Don't know why I didn't think to look for that. Thanks!
-
I looked at the FAQ and did a keyword search. There are lots of complaints about this but none that I saw either applied here or led to a solution.
I've got a home built computer with an LG WH10LS30 BD-RE writer. I'm using Verbatim single layer 16x dvd-r disks. Drivers are up to date.
Imgburn used to record pretty close to that speed and verify quickly. But lately, records are running around 5-6x and verifies are 0.7x. Yes, that's less than single speed. I've been fooling around with the off and on for a week and it has me baffled.
Log follows.
I 23:28:19 Source Media Supported Write Speeds: 8x, 12x, 16x
I 23:28:19 Source Media Sectors: 2,152,528 (Track Path: PTP)
I 23:28:19 Source Media Size: 4,408,377,344 bytes
I 23:28:19 Image File: -==/\/[bUILD IMAGE]\/\==-
I 23:28:19 Image File Sectors: 2,152,528 (MODE1/2048)
I 23:28:19 Image File Size: 4,408,377,344 bytes
I 23:28:19 Image File Volume Identifier: History
I 23:28:19 Image File Volume Set Identifier: UNDEFINED
I 23:28:19 Image File Application Identifier: ImgBurn v2.5.8.0 - The Ultimate Image Burner!
I 23:28:19 Image File Implementation Identifier: ImgBurn v2.5.8.0
I 23:28:19 Image File File System(s): ISO9660, Joliet
I 23:28:19 Read Speed (Data/Audio): MAX / MAX
I 23:28:20 Read Speed - Effective: 6.6x - 16x
I 23:28:20 Verifying Session 1 of 1... (1 Track, LBA: 0 - 2152527)
I 23:28:20 Verifying Track 1 of 1... (MODE1/2048, LBA: 0 - 2152527)
I 00:31:02 Exporting Graph Data...
I 00:31:02 Graph Data File: C:\Users\pjcamp\AppData\Roaming\ImgBurn\Graph Data Files\HL-DT-ST_BD-RE_WH10LS30_1.00_WEDNESDAY-SEPTEMBER-24-2014_11-21_PM_MCC_03RG20_MAX.ibg
I 00:31:02 Export Successfully Completed!
I 00:31:02 Operation Successfully Completed! - Duration: 01:02:41
I 00:31:02 Average Verify Rate: 1,144 KiB/s (0.8x) - Maximum Verify Rate: 2,086 KiB/s (1.5x)
Verify failed: Reason layouts do not match BUT
in ImgBurn Support
Posted
Sort of suspect that myself, either in Windows 10 or a driver or maybe firmware. Thanks for the help.