ch00se Posted February 28, 2011 Posted February 28, 2011 Hello! I've been using imgburn for sometime now and rarely had any problems. I was attempting to reburn a disc I had previous burnt using the same media as before and the same drive to burn, which is far from old. When the disc reaches the finalising stage however I get the internal target failure error. I've tried twice and updated imgburn inbetween but no luck. The drive isnt very old, a couple of years at most. I 14:02:41 ImgBurn Version 2.5.5.0 started! I 14:02:41 Microsoft Windows 7 Ultimate Edition (6.1, Build 7600) I 14:02:41 Total Physical Memory: 3,407,028 KB - Available: 1,983,404 KB I 14:02:41 Initialising SPTI... I 14:02:41 Searching for SCSI / ATAPI devices... I 14:02:42 -> Drive 1 - Info: PIONEER DVD-RW DVR-216D 1.06 (F:) (ATA) I 14:02:42 -> Drive 2 - Info: MagicISO Virtual DVD-ROM 1.0A (G:) (Unknown) I 14:02:42 Found 1 DVD-ROM and 1 DVD±RW! I 14:02:59 Operation Started! I 14:02:59 Source File: C:\Users\Rob\Desktop\DVD_ROM.dvd I 14:02:59 Source File Sectors: 3,827,488 (MODE1/2048) I 14:02:59 Source File Size: 7,838,695,424 bytes I 14:02:59 Source File Volume Identifier: DVD_ROM I 14:02:59 Source File Volume Set Identifier: ec67c000MS UDFBridge I 14:02:59 Source File Application Identifier: CDIMAGE 2.45 (12/06/2000 TM) I 14:02:59 Source File Implementation Identifier: Microsoft CDIMAGE UDF I 14:02:59 Source File File System(s): ISO9660, UDF (1.50) I 14:02:59 Destination Device: [0:0:0] PIONEER DVD-RW DVR-216D 1.06 (F:) (ATA) I 14:02:59 Destination Media Type: DVD+R DL (Disc ID: MKM-003-00) (Speeds: 2.4x, 4x, 6x, 8x, 10x) I 14:02:59 Destination Media Sectors: 4,173,824 I 14:02:59 Write Mode: DVD I 14:02:59 Write Type: DAO I 14:02:59 Write Speed: 2.4x I 14:02:59 Link Size: Auto I 14:02:59 Lock Volume: Yes I 14:02:59 Test Mode: No I 14:02:59 OPC: No I 14:02:59 BURN-Proof: Enabled I 14:02:59 Write Speed Successfully Set! - Effective: 3,324 KB/s (2.4x) I 14:02:59 Advanced Settings - Optimal Writing Speed: No I 14:03:00 Optimal L0 Data Zone Capacity: 1,913,760 I 14:03:00 Optimal L0 Data Zone Method: Copied From Original Disc I 14:03:33 Set L0 Data Zone Capacity Succeeded! I 14:03:33 Filling Buffer... (40 MB) I 14:03:34 Writing LeadIn... I 14:03:35 Writing Session 1 of 1... (1 Track, LBA: 0 - 3827487) I 14:03:35 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 3827487) I 14:03:35 Writing Layer 0... (LBA: 0 - 1913759) I 14:23:52 Writing Layer 1... (LBA: 1913760 - 3827487) I 14:44:21 Synchronising Cache... I 14:44:23 Closing Track... I 14:44:34 Finalising Disc... W 14:44:53 Potential 'WaitImmediateIO' Deferred Error - (0%, 0/3) - Unknown (Internal Target Failure) (ASC: 0x44, ASCQ: 0xD6) W 14:44:53 Finalise Disc Failed! - Reason: Unknown (Internal Target Failure) (ASC: 0x44, ASCQ: 0xD6) W 14:44:53 Retrying (1 of 3)... W 14:45:02 Potential 'WaitImmediateIO' Deferred Error - (0%, 0/3) - Unknown (Internal Target Failure) (ASC: 0x44, ASCQ: 0xD6) W 14:45:02 Retry Failed - Reason: Unknown (Internal Target Failure) (ASC: 0x44, ASCQ: 0xD6) W 14:45:02 Retrying (2 of 3)... W 14:45:06 Potential 'WaitImmediateIO' Deferred Error - (0%, 0/3) - Unknown (Internal Target Failure) (ASC: 0x44, ASCQ: 0xD6) W 14:45:06 Retry Failed - Reason: Unknown (Internal Target Failure) (ASC: 0x44, ASCQ: 0xD6) W 14:45:06 Retrying (3 of 3)... W 14:45:15 Potential 'WaitImmediateIO' Deferred Error - (0%, 0/3) - Unknown (Internal Target Failure) (ASC: 0x44, ASCQ: 0xD6) W 14:45:15 Retry Failed - Reason: Unknown (Internal Target Failure) (ASC: 0x44, ASCQ: 0xD6) Does anyone have any input? Thanks
Rincewind Posted February 28, 2011 Posted February 28, 2011 (edited) Try cleaning your drive with a cleaning disc, it couldn't hurt. Also your firmware version is 1.06, there is an update: http://www.firmwarehq.com/download_104-file_DVR-216D_FW109EU2.EXE.html After updating your firmware try again. Edited February 28, 2011 by Rincewind
Recommended Posts