jmatt26946 Posted September 14, 2011 Share Posted September 14, 2011 So thats what pops up every time I get half way or all the way through burning a DL disk. I use Verbatim and never used to have issues burning. I 16:07:32 Test Mode: No I 16:07:32 OPC: No I 16:07:32 BURN-Proof: Enabled I 16:07:34 Write Speed Successfully Set! - Effective: 8,310 KB/s (6x) I 16:07:34 Book Type Setting: DVD-ROM I 16:07:34 Optimal L0 Data Zone Capacity: 1,913,760 I 16:07:34 Optimal L0 Data Zone Method: Copied From Original Disc I 16:07:57 Set L0 Data Zone Capacity Succeeded! I 16:07:57 Filling Buffer... (40 MB) I 16:07:58 Writing LeadIn... I 16:08:21 Writing Session 1 of 1... (1 Track, LBA: 0 - 3827487) I 16:08:21 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 3827487) I 16:08:21 Writing Layer 0... (LBA: 0 - 1913759) I 16:19:40 Writing Layer 1... (LBA: 1913760 - 3827487) I 16:32:07 Synchronising Cache... I 16:32:26 Closing Track... I 16:32:48 Finalising Disc... I 16:33:40 Exporting Graph Data... I 16:33:40 Graph Data File: C:\Users\John\AppData\Roaming\ImgBurn\Graph Data Files\TSSTcorp_CDDVDW_TS-L633C_SN01_WEDNESDAY-SEPTEMBER-14-2011_4-07_PM_MKM-003-00_MAX.ibg I 16:33:40 Export Successfully Completed! I 16:33:40 Operation Successfully Completed! - Duration: 00:26:09 I 16:33:40 Average Write Rate: 5,368 KB/s (3.9x) - Maximum Write Rate: 8,487 KB/s (6.1x) I 16:33:40 Cycling Tray before Verify... W 16:41:59 Waiting for device to become ready... I 16:42:16 Device Ready! E 16:42:16 CompareImageFileLayouts Failed! - Session Count Not Equal (1/0) E 16:42:16 Verify Failed! - Reason: Layouts do not match. Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted September 14, 2011 Share Posted September 14, 2011 Post the whole log please. It looks like your drive is just doing a bad job of burning those discs. Slimline drives don't make for good burners. Try selecting one of the slower supported write speeds. Cleaning the drive with a cleaning disc may help too. Did the problem start when you got a new spindle of discs? Maybe they're faulty or not quite identical to your last ones. Link to comment Share on other sites More sharing options...
jmatt26946 Posted September 14, 2011 Author Share Posted September 14, 2011 Post the whole log please. It looks like your drive is just doing a bad job of burning those discs. Slimline drives don't make for good burners. Try selecting one of the slower supported write speeds. Cleaning the drive with a cleaning disc may help too. Did the problem start when you got a new spindle of discs? Maybe they're faulty or not quite identical to your last ones. I am already writing it at 2.4x and every disk ive used has done this. and that was my whole log. any recommendations? Link to comment Share on other sites More sharing options...
mmalves Posted September 15, 2011 Share Posted September 15, 2011 The piece of the log you posted shows that disc was burned at max speed (6x with your drive/firmware/media combination). All that you can try has already been outlined above by LUK. Link to comment Share on other sites More sharing options...
jmatt26946 Posted September 15, 2011 Author Share Posted September 15, 2011 The piece of the log you posted shows that disc was burned at max speed (6x with your drive/firmware/media combination). All that you can try has already been outlined above by LUK. None of those things worked. Does anyone have anything I can try? it used to work just fine. Maybe downgrading to an older version? Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted September 15, 2011 Share Posted September 15, 2011 The software has nothing to do with, it's a hardware error. Your drive has supposedly burnt the disc ok, but the disc still just looks blank after the tray has been cycled and Verify is about to start - hence the error. Link to comment Share on other sites More sharing options...
Recommended Posts