hiratio Posted December 6, 2011 Posted December 6, 2011 Hi. I'm new to all this new burning of XGD3 with your imgburn,I'm not getting any errors when i burn,however what is happening with me is when i place my disc in to the xbox drive it boots up does what it's suppose to, gets to the same spot every time and then an error message pops up on the telly,disc unreadable,gives me a suggestion,wipe/clean disc then re-insert,the game is modern warfare 3 ripped from the Lite-On 0800 v3 and burnt with latest imgburn.What i did was stuck the original game in to see what happens,all worked fine,so then i replaced the disc with my backup and works fine ? Iv'e looked everywhere i could think of to seek an answer to this but to no avail,I don't want this happening to me all the time .I have supplied my log,is there anything obvious sticking out that is wrong? I thought i had followed the tutorial to the letter,maybe not? maybe it's not imgburn related I don't know,no errors come up in the latest xbc either.I use to have the xkey in this Phat console but removed it and put it into my slim 360,any suggestions? Thanks. The discs I am using are Verbatims from singapore but as you can see in the log it says ritek. ImgBurn.log
LIGHTNING UK! Posted December 6, 2011 Posted December 6, 2011 Why didn't you verify the disc? I've never seen Verbatim discs with the RITEK MID so they must be new/fake or you've got confused somewhere. Either way, it still comes down to you needing MKM-001-00 or MKM-003-00 discs. Personally I'd go for the MKM-003-00 discs with the LiteOn drives.
hiratio Posted December 6, 2011 Author Posted December 6, 2011 Why didn't you verify the disc? I've never seen Verbatim discs with the RITEK MID so they must be new/fake or you've got confused somewhere. Either way, it still comes down to you needing MKM-001-00 or MKM-003-00 discs. Personally I'd go for the MKM-003-00 discs with the LiteOn drives. Thankyou for the reply,I have just realised they are TDK so my apoligies for that,that's why they have ritek,I realise it is said that Verbatim is the preferred disc but me using the TDK's(under advisement from a modder,for burn and playable quality,as TDK's are more expensive than Verbatims where I'm from) and they are working,no errors on imgburn or xbc,surely that wouldn't give me the unreadable disc about 5 minutes into the game would it?...TDK is just as good as Verbatim.Ill duck out and grab a few Verbatims and just see.
hiratio Posted December 6, 2011 Author Posted December 6, 2011 (edited) Why didn't you verify the disc? I've never seen Verbatim discs with the RITEK MID so they must be new/fake or you've got confused somewhere. Either way, it still comes down to you needing MKM-001-00 or MKM-003-00 discs. Personally I'd go for the MKM-003-00 discs with the LiteOn drives. Ok...verified the burn,now I'm getting errors,Is this where the discs come into play,by that i mean as you pointed out with Verbatim over TDK ? I/O Error Device:[4.0]Atapi Ihas124 B ALOS (E)ATA SCI Status 0x02 Interpretation:Check Condition CDB 28 00 00 20 3B E1 00 00 01 00 Interpretation:Read(10)-Sector:2112481 Sense Area 70 00 03 00 00 00 00 0A 00 00 00 00 11 05 00 00 00 00 Interpretation: L-EC Uncorrectable error does the above tell you anything ? disc related,hardware or I'm simply doing something wrong ? ImgBurn 2.log Edited December 6, 2011 by hiratio
LIGHTNING UK! Posted December 6, 2011 Posted December 6, 2011 Yes, it's the disc. You're overburning them (thanks to the firmware mod) and Verbatim discs are the ones that cope with that the best. The others fail around the (now extended) layer break position - just as yours did there.
hiratio Posted December 6, 2011 Author Posted December 6, 2011 Yes, it's the disc. You're overburning them (thanks to the firmware mod) and Verbatim discs are the ones that cope with that the best. The others fail around the (now extended) layer break position - just as yours did there. Ok,thankyou very much appreciated,yes I know I should of used Verbatims,but as explained previously I was only going by what my modder said to use and to be honest I never gave it a second thought.the last backup i did couldn't even be read by the drive after verifying,but the first disc booted up and then come up with unreadable disc around the 4-5 minute mark(unverified) so in essence imgburn picked up the errors on the second burn(verified) and prevented it from booting,does that sound feasable? I now know it's the disc(s) but I'm trying to get my head around the first one booting and the second one not booting.
LIGHTNING UK! Posted December 6, 2011 Posted December 6, 2011 ImgBurn didn't prevent anything from happening. The verify process just warns you of potential issues with the disc - like it not being 100% readable.
hiratio Posted December 6, 2011 Author Posted December 6, 2011 ImgBurn didn't prevent anything from happening. The verify process just warns you of potential issues with the disc - like it not being 100% readable. Yes I know what you mean,I should of worded it better,just an early start for me down here and trying to get the brain into gear But Thanks Again.....
Recommended Posts