Jump to content

Recommended Posts

Posted

My OS is Wndows 10 Version 1803. I'm trying to create an ISO file from a Windows 7 Ent SP1 DVD.I notice the activity light of my computer's DVD drive is never lit as ImgBurn says it's reading from DVD and writing to disk. See the attached file for error and log information. Please advise. Thanks!

post-57566-0-35639900-1526917546_thumb.png

Posted

I see a rather odd Warning I've never seen before: "Found end of disc." 

 

 

I don't know this error but since the resulting image file you tried to mount appears to be corrupted, the problem would seem to be either your drive thinks it found the end of the disc when it wasn't the end of the disc or the disc you're trying to read has gone bad.

 

 

Barring trying to read this disc in another drive, that's about all I can say to try.  Try to read the disc in another drive.  If you still get the same error, then it would seem there's something wrong with the Windows 7 disc you're trying to read.

Posted

I tried a different DVD drive (USB) and ImgBurn worked. I also tried creating the ISO with the original internal drive and other software (InfraRecorder) and was successful. I guess there's something about ImgBurn paired with my internal drive that's causing a problem. Here's the data from the disc info box:

 

PLDS DVD+-RW DU-8A5LH 6D1M (RAID)
Current Profile: DVD-ROM
 
Disc Information:
Status: Complete
State of Last Session: Complete
Erasable: No
Sessions: 1
Sectors: 1,553,337
Size: 3,181,234,176 bytes
Time: 345:13:12 (MM:SS:FF)
Supported Read Speeds: 2x, 4x, 6x, 8x
Current Read Speed: 1.7x - 4x
 
TOC Information:
Session 1... (LBA: 0)
-> Track 01  (Mode 1, LBA: 0 - 1553336)
-> LeadOut  (LBA: 1553337)
 
Track Information:
Session 1...
-> Track 01 (LTSA: 16580608, LTS: 1, LRA: 0)
 
Physical Format Information (Last Recorded):
Book Type: DVD-ROM
Part Version: 0
Disc Size: 120 mm
Maximum Read Rate: 2.52 Mbps
Number of Layers: 1
Track Path: Parallel Track Path (PTP)
Linear Density: 0.267 um/bit
Track Density: 0.74 um/track
First Physical Sector of Data Area: 0
Last Physical Sector of Data Area: 0
Last Physical Sector in Layer 0: 0
Posted
I can understand this:

 

"First Physical Sector of Data Area: 0"

 

but the next ones don't make much sense to me:

 

Last Physical Sector of Data Area: 0

Last Physical Sector in Layer 0: 0

 

 

It seems like the drive isn't returning information for these values.  In fact, would the first sector be listed as 0?  Is there a Sector 0, given that computers start numbering at 0?

Posted

ImgBurn uses the 'Track Information' values and they're not right either.

 

Track Information:

Session 1...

-> Track 01 (LTSA: 16580608, LTS: 1, LRA: 0)

LTSA is Logical Track Start Address

LTS is Logical Track Size

 

So this is just a drive / media combo issue.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.