sargey Posted February 18, 2007 Share Posted February 18, 2007 Hi guys. I'm getting speed issues with imgburn. I installed it on friday and it was working fine. As of yesterday I cannot seem to get over 1.2x. I have read the faq and I have done as it says. (Delete the controllers etc). Any ideas? It seem strange that it was working ok, then just stopped??? Link to comment Share on other sites More sharing options...
dontasciime Posted February 18, 2007 Share Posted February 18, 2007 run this then reboot see what happens if you using usb then check cables Run right click it and save target as Link to comment Share on other sites More sharing options...
sargey Posted February 18, 2007 Author Share Posted February 18, 2007 Thanks for the reply. I get the following message "No resettable ATA channels with windows drivers found. Nothing changed." Anything else I can try? Link to comment Share on other sites More sharing options...
dontasciime Posted February 18, 2007 Share Posted February 18, 2007 how have you got the drives connected as it would appear you have no controller in at all try nero info tool and configuration see what it says ftp://ftp6.nero.com/tools/InfoTool.zip which operating system are you using open up device manager and scan for new hardware Link to comment Share on other sites More sharing options...
sargey Posted February 18, 2007 Author Share Posted February 18, 2007 No, wires are connected, disc's burn, just only at 1.2x max. Using win xp pro sp2. No new hardware when I scan. I have attached infotool text from nero software, if you wouldn't mind having a look at it? InfoTool.txt Link to comment Share on other sites More sharing options...
dontasciime Posted February 18, 2007 Share Posted February 18, 2007 Might be me but seems you have both hard drives set to master. I must be reading it wrong which motherboard is it ? (actually i looked again its a dell) Can you verify how you have your hard drives and writers connected. also you using an add in IDE pci card ? Link to comment Share on other sites More sharing options...
dontasciime Posted February 18, 2007 Share Posted February 18, 2007 can you run it again with just configuration ticked when you save log Nero InfoTool 4.1.0.8 Interface Information --------------------- Adapter 1 --------- Description : Primary IDE Channel Driver Description : system32\DRIVERS\atapi.sys Company : Microsoft Corporation Version : 5.1.2600.2180 (xpsp_sp2_rtm.040803-2158) Description : IDE/ATAPI Port Driver Attached Devices Description : Master: Maxtor 6B200P0 Type : Disk Drive DMA : On Description : Slave: BENQ DVD-ROM 16X Type : CD-Rom Drive DMA : On Autorun : On Adapter 2 --------- Description : Secondary IDE Channel Driver Description : system32\DRIVERS\atapi.sys Company : Microsoft Corporation Version : 5.1.2600.2180 (xpsp_sp2_rtm.040803-2158) Description : IDE/ATAPI Port Driver Attached Devices Adapter 3 --------- Description : Primary IDE Channel Driver Description : system32\DRIVERS\atapi.sys Company : Microsoft Corporation Version : 5.1.2600.2180 (xpsp_sp2_rtm.040803-2158) Description : IDE/ATAPI Port Driver Attached Devices Description : Master: HDS722525VLSA80 Type : Disk Drive DMA : On Adapter 4 --------- Description : Secondary IDE Channel Driver Description : system32\DRIVERS\atapi.sys Company : Microsoft Corporation Version : 5.1.2600.2180 (xpsp_sp2_rtm.040803-2158) Description : IDE/ATAPI Port Driver Attached Devices Description : Master: Maxtor 6B300S0 Type : Disk Drive DMA : On Adapter 5 --------- Description : Primary IDE Channel Driver Description : system32\DRIVERS\atapi.sys Company : Microsoft Corporation Version : 5.1.2600.2180 (xpsp_sp2_rtm.040803-2158) Description : IDE/ATAPI Port Driver Attached Devices Adapter 6 --------- Description : Secondary IDE Channel Driver Description : system32\DRIVERS\atapi.sys Company : Microsoft Corporation Version : 5.1.2600.2180 (xpsp_sp2_rtm.040803-2158) Description : IDE/ATAPI Port Driver Attached Devices Description : Master: PIONEER DVD-RW DVR-108 Type : CD-Rom Drive DMA : On Autorun : On Description : Slave: WDC WD2500JB-22GVC0 Type : Disk Drive DMA : On Link to comment Share on other sites More sharing options...
dontasciime Posted February 18, 2007 Share Posted February 18, 2007 you got sata hard drives then Link to comment Share on other sites More sharing options...
dontasciime Posted February 18, 2007 Share Posted February 18, 2007 open up the one your benq is connected to and advanced settings tab and look for udma 2 or udma 4 then uninstall that controller reboot computer and let windows pick it up again. have you recently been in the Bios as well, maybe you changed something in there, look for IDE section and see if there is an option to scan or refresh devices Link to comment Share on other sites More sharing options...
sargey Posted February 18, 2007 Author Share Posted February 18, 2007 Just the config in this text file. I'm off to uninstall the channels and reboot. brb. InfoTool.txt Link to comment Share on other sites More sharing options...
dontasciime Posted February 18, 2007 Share Posted February 18, 2007 you should maybe as well check all the hard drives you have connected for errors, just tick top box though. also if you still get nowhere whatever the other dvd rom showing as scsi you have is, unplug the cable and power cable and try again Link to comment Share on other sites More sharing options...
sargey Posted February 18, 2007 Author Share Posted February 18, 2007 That seems to be it! Just started burning againg and getting 7.8x! Thanks for your help mate! Link to comment Share on other sites More sharing options...
dontasciime Posted February 18, 2007 Share Posted February 18, 2007 no problem your welcome. Link to comment Share on other sites More sharing options...
Recommended Posts