shen293 Posted February 13, 2009 Posted February 13, 2009 Why is it when I put it in "test mode" I get successful outcome and this is the log: I 22:45:53 ImgBurn Version 2.4.2.0 started! I 22:45:53 Microsoft Windows XP Media Center Edition (5.1, Build 2600 : Service Pack 3) I 22:45:53 Total Physical Memory: 981,480 KB - Available: 622,616 KB W 22:45:53 Drive D:\ (FAT32) does not support single files > 4 GB in size. I 22:45:53 Initialising SPTI... I 22:45:53 Searching for SCSI / ATAPI devices... I 22:45:53 Found 1 DVD-ROM and 1 DVD
Cynthia Posted February 13, 2009 Posted February 13, 2009 I 23:09:45 Destination Device: [2:0:0] HP DVD Writer 740b HJ24 (E:) (ATA)I 23:09:45 Destination Media Type: DVD-R (Disc ID: MCC 03RG20) (Speeds: 4x) According to the info about your burner - it's a 16x writer. Despite this - the firmware only supports your media at 4x speed and the question is how well it is adopted for that media and according to your logs - it's not. Test mode test the included 'moves' of the laser head and that seems to work well. The issue happens when the laser light is turned on and it can't write very good to your media. It should be cheaper to get a new writer than spending a fortune on coasters. I do not know the prices in your country - but here a new good writer costs around what I have to pay for 35 Verbatims discs (including media tax ).
shen293 Posted February 14, 2009 Author Posted February 14, 2009 Sorry,Cynthia but so that we are just on the right page Are you recommending me to get a new writer? (internal?) And 1 extra question.... I have a HP writer on a HP desktop, can I buy a different brand of writer other than HP and install it into my HP desktop? thank you
Cynthia Posted February 14, 2009 Posted February 14, 2009 Yes, a new writer should solve your issues. Try to get one that is rated high regarding quality in the various burning forums. You can add any brand in it.
shen293 Posted February 14, 2009 Author Posted February 14, 2009 ok..thanks a lot for the advice really appreciate it =)
shen293 Posted February 16, 2009 Author Posted February 16, 2009 (edited) Oh and also...what does the error Invalid Address For Write really mean? Like was it more of a DVD burner failure or something... Just figuring things out..cause I'm planning to get an internal burner but don't know how to remove my current burner So yea..help me out n thanks Edited February 16, 2009 by shen293
Cynthia Posted February 16, 2009 Posted February 16, 2009 The problem is normally seen if the media is defective or not working well with the DVD burner. It could also be a media type which is not supported by the burner.
mmalves Posted February 16, 2009 Posted February 16, 2009 'Invalid Address For Write' is pretty self-explanatory: the burner "says" that when the address you're trying to write isn't available for some reason (e.g. it was already written to, it's beyond the disc's capacity, etc). What is weird is that the 'Invalid Address For Write' error is usually collateral to another error, like 'Write Error' and similar. Replacing the drive is easy: read this how-to for the general guidelines. I'd like to add that you should use a 80-wire cable (buy one if the one you're using isn't 80-wire). If you're going to buy the new burner in a computer shop I'm pretty sure they can replace the old one for free
shen293 Posted February 16, 2009 Author Posted February 16, 2009 I see...but I believe that if I get a new burner... It doesn't really tell me which media its gonna support.. Or at least I think as this is gonna be my first time purchasin a burner As u said b4 tho...can that error be possibly bcos my burners dead...I was trying to find that out but wasting alot on coasters And I hate it
Cynthia Posted February 16, 2009 Posted February 16, 2009 I Pioneer should solve your problems. I have one with the same type of disc (MCC 03RG20) that you got errors with. Here is also a list of the media id's that Pioneer supports with the recent writers. http://wwwbsc.pioneer.co.jp/product-e/ibs/.../DVR116_109.pdf I 08:40:14 ImgBurn Version 2.4.2.0 started!I 08:40:14 Microsoft Windows Vista Ultimate Edition (6.0, Build 6001 : Service Pack 1) I 08:40:14 Total Physical Memory: 2 095 484 KB - Available: 1 026 016 KB I 08:40:14 Initialising SPTI... I 08:40:14 Searching for SCSI / ATAPI devices... I 08:40:17 Found 2 DVD
shen293 Posted February 16, 2009 Author Posted February 16, 2009 (edited) Thanks for the heads up...a Pioneer burner:.thx I looked through the supported media... And I can't seem to find verbatim... It's most likely be able to support it yea? Edited February 16, 2009 by shen293
mmalves Posted February 16, 2009 Posted February 16, 2009 Verbatim uses dyes manufactured by Mitsubishi Chemical Corporation (MCC a.k.a. MKM) and Taiyo Yuden (TYG02/TYG03), so yes, they're supported by that burner.
shen293 Posted February 16, 2009 Author Posted February 16, 2009 Ok thx...simply speakin tho... Why is an internal burner better than an external ones? Is it because external tends to fail more in burning wise:. Sry I know this is not the right section...I apologiZe
mmalves Posted February 16, 2009 Posted February 16, 2009 External interfaces (USB/FireWire/etc) are slower and less reliable than internal interfaces (IDE/SATA/etc). Not to mention that an external burner is more prone to bumps/dropping/etc. May I ask why are you so reluctant in buying a new internal burner to replace the broken one you have? A new burner is as cheap as a spindle of DVDs these days.
shen293 Posted February 16, 2009 Author Posted February 16, 2009 It's not that I'm reluctant or anything... Its that I'm not sure which drivers my desktop is compatible with and the fact that I dont even know how to remove my broken burner...I tried taking it out but it seems stuck I read through some articles about the drives .. and I realize something about IDE and SATA and since under my device manager i have like 2 primary and 2 secondary IDE channels.. so am I right to think that the burners I should get should be in IDE? or it doesn't even matter?
mmalves Posted February 16, 2009 Posted February 16, 2009 It does matter, as the IDE and SATA interfaces are different from each other. Your burner specifications can be found here and it uses IDE interface, so you should get a new burner with IDE interface.
shen293 Posted February 16, 2009 Author Posted February 16, 2009 ok cool, thanks appreciate it alot I've heard around that ppl say Pioneer's burners are reliable.. so I was wondering what do you guys think of this: Pioneer Black 20X DVD+R 8X DVD+RW 12X DVD+R DL 20X DVD-R 6X DVD-RW 16X DVD-ROM 40X CD-R 32X CD-RW 40X CD-ROM 2MB Cache IDE 20X DVD
mmalves Posted February 16, 2009 Posted February 16, 2009 That's a very good burner from what I've read. I think Cynthia has one of those, so she can tell you how good or bad it is
shen293 Posted February 16, 2009 Author Posted February 16, 2009 haha thats nice to know ok thats alot mmalves.. im pretty sure im getting that burner and once I installed it and burn I'll keep you updated with results.. hopefully good results ... dislike wasting on coasters thanks again
Cynthia Posted February 16, 2009 Posted February 16, 2009 That's a very good burner from what I've read. I think Cynthia has one of those, so she can tell you how good or bad it is I did, in post #10.
shen293 Posted February 16, 2009 Author Posted February 16, 2009 XD wonder how'd I miss that Thats cool, i'll be getting the same one something outa topic ....so.. was the installation easy tho?
Cynthia Posted February 17, 2009 Posted February 17, 2009 With a SATA you only need to connect two cables. With a PATA as your ordered it's just that + you also have to set a switch in the back of the burner to either Master, Slave or Cable Select. Put the new burner as Master and connect it to the end of the cable and your old reader/writer to slave and put it in the middle of the cable. It's easy and there are plenty of guides with pictures on the net if you should need it.
Recommended Posts