i select speed 2.4 and it burns at 4.0

[Merkery]

title says it all pretty much when i select a speed of 2.4 it still burns at 4.0

 

also ive noticed that it gets to 100 percent the disk drive opens and then closes and starts burning aagain

 

any suggestions?

[LOCOENG]

Post a log of your problem.

 

The second part is the verification, it's not burning.

[Merkery]

well it wouldnt be logged its as simple as i select 2.4x burn speed and whilst its writing it goes at 4.0x and do i need to verify my disks? cause its an additional 20 minutes

[Merkery]

anyway not to undermind you this is what im doign as we speak as you see ive selected write speed of 2 this time it is going at 4 as it writes

 

I 00:44:25 Operation Started!

I 00:44:25 Source File: E:\Games Factory\New Folder\dgr-svsr2k9.dvd

I 00:44:25 Source File Sectors: 3,697,696 (MODE1/2048)

I 00:44:25 Source File Size: 7,572,881,408 bytes

I 00:44:25 Source File Volume Identifier: XGD2DVD_NTSC

I 00:44:25 Source File Volume Set Identifier: 34672923

I 00:44:25 Source File Implementation Identifier: Sonic Scenarist 3.1

I 00:44:25 Source File File System(s): ISO9660, UDF (1.02)

I 00:44:25 Destination Device: [1:0:0] HL-DT-ST DVD-RAM GH22NP20 1.02 (D:) (ATA)

I 00:44:25 Destination Media Type: DVD+R DL (Disc ID: RICOHJPN-D01-67) (Speeds: 4x, 6x, 8x)

I 00:44:25 Destination Media Sectors: 4,173,824

I 00:44:25 Write Mode: DVD

I 00:44:25 Write Type: DAO

I 00:44:25 Write Speed: 2x

I 00:44:25 Link Size: Auto

I 00:44:25 Test Mode: No

I 00:44:25 OPC: No

I 00:44:25 BURN-Proof: Enabled

I 00:44:25 Book Type Setting: DVD-ROM

I 00:44:25 Optimal L0 Data Zone Capacity: 1,913,760

I 00:44:25 Optimal L0 Data Zone Method: Copied From Original Disc

I 00:44:25 Filling Buffer... (20 MB)

I 00:44:25 Writing LeadIn...

I 00:45:00 Writing Session 1 of 1... (1 Track, LBA: 0 - 3697695)

I 00:45:00 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 3697695)

I 00:45:00 Writing Layer 0... (LBA: 0 - 1913759)

I 00:57:27 Writing Layer 1... (LBA: 1913760 - 3697695)

[LOCOENG]

I 00:44:25 Destination Media Type: DVD+R DL (Disc ID: RICOHJPN-D01-67) (Speeds: 4x, 6x, 8x)

 

2.4X isn't supported by your firmware/burner so all you have to choose from is 4X, 6X, and 8X.

 

There is a firmware update available for your burner which may give you more speeds to choose from...1.03 from here ~ http://www.firmwarehq.com/LG/GH22NP20/files.html

 

It's not required to verify your burns, but it does serve a purpose.