Jump to content
kokwkz

HELP IMGburn freeze on stuck on 50%

Recommended Posts

hello

i kindly your appreciated support as this is the 8th DVD that i tried to burn DVD (backup XBOX360) and always freeze at 50% BUFFER 100% buffer device 0%

 

please find the logs 

 

 

 

I 20:48:35 Operation Started!
I 20:48:35 Source File: C:\Users\nelly\Desktop\just dance kids\Just Dance Kids 2014 [RF][Kinect].dvd
I 20:48:35 Source File Sectors: 4,267,015 (MODE1/2048)
I 20:48:35 Source File Size: 8,738,846,720 bytes
I 20:48:35 Source File Volume Identifier: DVD_ROM
I 20:48:35 Source File Volume Set Identifier: 5f7c8000MS UDFBridge
I 20:48:35 Source File Application Identifier: CDIMAGE 2.45 (12/06/2000 TM)
I 20:48:35 Source File Implementation Identifier: Microsoft CDIMAGE UDF
I 20:48:35 Source File File System(s): ISO9660, UDF (1.50)
I 20:48:35 Destination Device: [0:1:0] HL-DT-ST DVDRAM GUE0N T.02 (E:) (SATA)
I 20:48:35 Destination Media Type: DVD+R DL (Disc ID: CMC MAG-D03-64)
I 20:48:35 Destination Media Supported Write Speeds: 2.4x, 4x, 6x
I 20:48:35 Destination Media Sectors: 4,173,824
I 20:48:35 Destination Media L0 Data Zone Capacity: 2,086,912 (Changeable: Yes)
I 20:48:35 Write Mode: DVD
I 20:48:35 Write Type: DAO
I 20:48:35 Write Speed: 2.4x
I 20:48:35 DVD+R DL Reserve Track: No
I 20:48:35 Link Size: Auto
I 20:48:35 Lock Volume: Yes
I 20:48:35 Test Mode: No
I 20:48:35 OPC: No
I 20:48:35 BURN-Proof: Enabled
I 20:48:35 Write Speed Successfully Set! - Effective: 3,324 KB/s (2.4x)
I 20:48:35 Book Type Setting: N/A (Reason: Invalid Command Operation Code)
W 20:48:35 User specified layer break position exceeds L0 capacity.
W 20:48:35 User Specified L0 Sectors: 2,133,520
W 20:48:35 Maximum L0 Sectors: 2,086,912
I 20:48:35 User Specified L0 Data Zone Capacity: 2,133,520
W 20:48:35 Set L0 Data Zone Capacity Failed! - Reason: Invalid Field in CDB
I 20:48:35 L0 Data Zone Capacity - Effective: 2,086,912
I 20:48:37 Filling Buffer... (73 MiB)
I 20:48:38 Writing LeadIn...
I 20:49:26 Writing Session 1 of 1... (1 Track, LBA: 0 - 4267014)
I 20:49:26 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 4267014)
I 20:49:26 Writing Layer 0... (LBA: 0 - 2086911)
I 21:11:55 Writing Layer 1... (LBA: 2086912 - 4267014)
W 21:12:55 Failed to Write Sectors 2089088 - 2089119 - Reason: Write Error
W 21:12:55 Retrying (1 of 20)...

NOTE : i use BENQ DVD which is a good one 

pleaseeee i need your expert support what should i do !!!

Share this post


Link to post
Share on other sites

You say you use BENQ DVD which is a good one, but this line of log betrays that:

I 20:48:35 Destination Media Type: DVD+R DL (Disc ID: CMC MAG-D03-64)

 

There is only one quality manufacturer of DVD+R DL and that's Verbatim DataLife Plus.  NOT the Life Series you find in stores; those are CMC.  You can only find the DataLife Plus stuff online.  CMC is the worst manufacturer of optical media out there.  About half the problems we see on this board are caused by cheap media, and CMC is the cheapest.  Ironically, they now OWN Verbatim but, at least, haven't changed the manufacturing process... YET!  :rolleyes:  Most problems people have on this board disappear when they switch from CMC to DataLife Plus Verbatim, and I expect your problem would go away, too.

 

Notice the write error is shortly after the layer change from 0 to 1?  DL media failure will more often than not occur at the layer change.

Share this post


Link to post
Share on other sites

hello DBminter

thank you so much for your support and reply but iam stuck with those DVDS so i need to know is there any work around to do as i notice also this that when change layer from 0 to 1 this is happen so is there any chance to solve it 

regards

 

Share this post


Link to post
Share on other sites

Switching discs is the cheapest and easiest method, but there MAY be others.  Not guaranteed to work, but they may.

 

1.) replace your DVD burner with a different make, manufacturer, and model.  No guarantee any new burner will like those CMC's any better than yours, but there's always the possibility.  The easiest way to do this is to try USB external burners.

2.) check for a firmware update for your DVD burner.  In Write mode, right click on the drive letter of your burner on the left hand side and choose the Check for firmware update option near the bottom of the context menu.  No guarantee a firmware update will fix the problem.  And, in some cases like Pioneer, firmware updates can make a drive WORSE:o

Share this post


Link to post
Share on other sites

×

Important Information

By using this site, you agree to our Terms of Use.