Jump to content


  • Posts

  • Joined

  • Last visited

JimmyW's Achievements

ISF Newbie

ISF Newbie (1/5)

  1. I'm trying to butn a 4GB file, and ImgBurn issues the warning about the file system. I comply by selecting UDF. However, ImgBurn will not butn the disc, but hangs indefinitely at the "Writing LeadIn" point. Canceling the job is impossible, short of a hard reboot of the sytstem. I attached the log. ImgBurn.log
  2. I am trying to burn a DVD and include some files with very long names that include Unicode and possibly illegal characters. I attached the log, which shows how far I can get. I'm using the default settings, and five file names were modified (I had to delete the file names from the log). Thanks. log.txt
  3. When I try to cancel a job, ImgBurn does not cancel the job, but remains open. I am trying to cancel the job at the point where the buffer is 100% written. I can force ImgBurn to close by killing the process, which really doesn't end the proces, as it remains running. So, I can't re-open ImgBurn and must reboot.
  4. If I add a folder to my project, is there a way to open the files from within ImgBurn and remove certain files? Thanks.
  5. Thanks. I installed the Lite-On drive in a different system, which has an Intel S5520SC board, the the drive seems to work fine. Perhaps there was some type of conflict between the drive and the S2600COE MB.
  6. Same power as comes off the MB. I'm usuing external USB ports, which shouldn't matter. I do this all the time with hard drives.
  7. I have all kinds of adapters, complete with power. The drive connects to an adapter by SATA, and the adapter to the machine with USB 2.0.
  8. I tried some different media in both drives, although the media may not be the best available. I've used that media in many other burners, though not in Blu Rays. I swapped SATA cables and ports with both burners. Neither of the drives is recognized through a SATA-to-USB converter or through eSATA. I also tried to connect them to a SATA RAID controller, but the drive is not recognized. I can read media fine in both drives; just can't burn.
  9. Thanks. I tried with other discs, inclduing DVDs, and all failed. The RAM (64GB) is fine.
  10. I'll bump this thread to report that I have the same problems with a new, Lite-On Blu Ray drive. I tried a CD-R at 8x, and attached the log and a family tree screenshot. I also tried t burn a CD-R with Nero, and that process failed during verification. The files on the disc were corrupt in both cases. I'm going to switch the data cable to different SATA port to see whether that helps, or try a new cable. Another SATA optical drive in the same machine works fine. ImgBurn.log
  11. Thanks again. It failed at 8x, too. I'll report back after I replace the drive.
  12. Thanks very much. I tried a number of speeds down to 16x, and each failed. I switched CD brands (can't get Taiyo Yuden at the moment), and the other brand failed. I also tried a DVD, which failed, and the log for that operation is attached. I'm starting toi think that I have a bad drive. ImgBurn.log
  13. Thanks. The drive is connected to a MB controller. This is the Family Tree data: I 08:29:49 Device: [1:0:0] ASUS BW-12B1ST 1.03 (S:) (SAS) I 08:29:49 Family Tree: I 08:29:49 -> ACPI x64-based PC I 08:29:49 -> Microsoft ACPI-Compliant System I 08:29:49 -> PCI bus I 08:29:49 -> Intel® Xeon® Processor E5 Product Family/Core i7 IIO PCI Express Root Port 1a - 3C02 (VEN_8086&DEV_3C02 - Intel - pci) I 08:29:49 -> Intel® C608/C606/X79 chipset PCI Express Upstream Port - 1D74 (VEN_8086&DEV_1D74 - Intel - pci) I 08:29:49 -> Intel® C608/C606/X79 chipset Virtual Switch Port - 1D3F (VEN_8086&DEV_1D3F - Intel - pci) I 08:29:49 -> Intel® C600 Series Chipset SAS RAID (SATA mode) (VEN_8086&DEV_1D6A - Intel - iaStorS) I 08:29:49 -> CD-ROM Drive (ASUS BW-12B1ST SCSI CdRom Device) (Bus Number 0, Target Id 0, LUN 0)
  14. I have an Asus BW-12B1ST Blu Ray SATA drive, firmware 1.03 (no updates available), in which I am trying to burn CD-R discs. I attached the log, but every burn project fails. I aborted verification after the first few errors. I'm using generic CD-R discs. I can burn CD-Rs in a standard DVD drive in the same machine withou tany problems. Thanks for any help that you can offer. ImgBurn.log
  15. I didn't see a guide direclty on this point, but is there a specific setting to close a disc so that no additional objects can be added? Thanks.
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.