mediocrerevolution Posted September 19, 2006 Posted September 19, 2006 i know how to make an iso, however, when i go to burn it with imageburn it does this W 00:11:23 Drive D:\ (FAT32) does not support single files > 4 GB W 00:11:23 Drive F:\ (FAT32) does not support single files > 4 GB I 00:11:23 Initialising SPTI... I 00:11:23 Searching for SCSI / ATAPI devices... I 00:11:43 Found 1 DVD-ROM and 1 DVD?RW! I 00:18:10 Operation Started! I 00:18:10 Source File: C:\Documents and Settings\Owner\Desktop\TAKE_THE_LEAD.ISO I 00:18:10 Source File Sectors: 2,285,897 (MODE1/2048) I 00:18:10 Source File Size: 4,681,517,056 bytes I 00:18:11 Source File Volume Identifier: TAKE_THE_LEAD I 00:18:11 Source File Implementation Identifier: DVD Shrink I 00:18:11 Source File File System(s): ISO9660, UDF (1.02) I 00:18:11 Destination Device: [1:0:0] TSSTcorp CD/DVDW TS-L532A TI51 (E:) (ATA) I 00:18:11 Destination Media Type: DVD-R (Disc ID: TYG02) (Speeds: 2x, 4x, 8x) I 00:18:11 Destination Media Sectors: 2,298,496 I 00:18:11 Write Mode: DVD I 00:18:11 Write Type: DAO I 00:18:11 Write Speed: 8x I 00:18:11 Link Size: Auto I 00:18:11 Test Mode: No I 00:18:11 BURN-Proof: Enabled I 00:18:11 Filling Buffer... I 00:18:12 Writing LeadIn... I 00:18:23 Writing Image... I 00:29:45 Synchronising Cache... I 00:30:49 Image MD5: b635b5a3c3bfc3b2fbb84228c6d6c790 I 00:30:49 Operation Successfully Completed! - Duration: 00:12:39 I 00:30:49 Average Write Rate: 6,713 KB/s (4.8x) - Maximum Write Rate: 10,292 KB/s (7.4x) I 00:30:49 Cycling Tray before Verify... W 00:30:55 Waiting for device to become ready... W 00:31:08 Device Not Ready - Unable to Recover TOC W 00:31:08 Retrying (1 of 3)... I 00:31:08 Cycling Tray before Verify... W 00:31:13 Waiting for device to become ready... W 00:31:20 Retry Failed - Unable to Recover TOC W 00:31:20 Retrying (2 of 3)... I 00:31:20 Cycling Tray before Verify... W 00:31:24 Waiting for device to become ready... i can mount the iso virtually and watch it, but i cannont make it go onto a dvd, please help
LIGHTNING UK! Posted September 19, 2006 Posted September 19, 2006 Either the drive is just producing bad burns on that media or the drive isn't working properly as it just can't re-initialise the disc - hence the 'Unable to Recover TOC' message. A firmware update might help - if there is one available? Are you sure those are real TYG02 discs and not fakes?
mediocrerevolution Posted September 19, 2006 Author Posted September 19, 2006 i have gotten it to say successful burn, however, there is nothing on the dvd-r after it completes
LIGHTNING UK! Posted September 19, 2006 Posted September 19, 2006 Was that using 'test mode' by any chance? Test mode doesn't burn anything.
mediocrerevolution Posted September 19, 2006 Author Posted September 19, 2006 (edited) Was that using 'test mode' by any chance? Test mode doesn't burn anything. ive ran it in test mode, and in burn mode, i ran into problems when i treid to do burnmode with verify, but i turned that off however, the dvd still ends up blank, but unusable because my writer did right "something" to it also i know the iso is a good file becuase i mounted it on my computer and was able to watch it Edited September 19, 2006 by mediocrerevolution
LIGHTNING UK! Posted September 19, 2006 Posted September 19, 2006 I just meant that if you had 'Test Mode' enabled, you were much more likely to get a successful burn (because the drive isn't actually writing to the media) - but of course then the disc would still be blank (and no verify would take place). A normal burn + verify (without 'Test Mode') should complete just fine but yours seems unable to reinitialise the disc once it has burnt to it. Not much I can do about that I'm afraid.
blutach Posted September 20, 2006 Posted September 20, 2006 Was that using 'test mode' by any chance? I 00:18:11 Destination Device: [1:0:0] TSSTcorp CD/DVDW TS-L532A TI51 (E:) (ATA) No it's TSST mode. BWAHAHAHAHAAHAAHAHA Regards
Recommended Posts