Error when closing a disc

[6000RPM]

When trying to close a BD-XL disc with an open session:

 

After clicking "Cancel" ImgBurn continues to do something (e.g. GUI is not responding), however after a minute the disc becomes closed.

Media info dump after refresh:

HL-DT-ST BD-RE  WH14NS40 1.05 (SATA)
Current Profile: BD-ROM

Disc Information:
Status: Complete
State of Last Session: Complete
Erasable: No
Sessions: 1
Sectors: 48,092,160
Size: 98,492,743,680 bytes
Time: 10687:10:60 (MM:SS:FF)
MID: VERBAT-IMk-000
Supported Read Speeds: 2x, 5x, 6x
Current Read Speed: 2x - 6x, 6x - 2x

TOC Information:
Session 1... (LBA: 0)
-> Track 01  (Mode 1, LBA: 0 - 48092159)
-> LeadOut  (LBA: 48092160)

Track Information:
Session 1...
-> Track 01 (LTSA: 0, LTS: 47918944, LRA: 0)

Disc Definition Structure:
ISA0 Size: 4,096 clustors - Full: No
OSA0 Size: 4,096 clustors - Full: No
ISA1 Size: 4,096 clustors - Full: No
OSA1 Size: 4,096 clustors - Full: No
Certified: No
Scanned: No
Manufacturers Name: HLDS BD-DRIVE
Additional ID: HLDS-JB8VERA
Serial Number: I95A0930 5

BD Disc Information (L0):
Disc ID: VERBAT-IMk-000
Disc Type: BD-R
Disc Size: 120 mm
Disc Class: 1
Disc Version: 2
Number of Layers: 3
Layer Type: Writable
DVD Layer Present: No
CD Layer Present: No
Channel Bit Length: 55.87 nm (33 GB Per Layer)
Push-Pull Polarity: Positive
Recorded Mark Polarity: HTL
BCA Present: Yes
Maximum Transfer Rate: Not Specified
First PAA of Data Zone: 554,925,568
Last PAA of Data Zone: 48,396,408

BD Disc Information (L1):
Disc ID: VERBAT-IMk-000
Disc Type: BD-R
Disc Size: 120 mm
Disc Class: 1
Disc Version: 2
Number of Layers: 3
Layer Type: Writable
DVD Layer Present: No
CD Layer Present: No
Channel Bit Length: 55.87 nm (33 GB Per Layer)
Push-Pull Polarity: Positive
Recorded Mark Polarity: HTL
BCA Present: Yes
Maximum Transfer Rate: Not Specified
First PAA of Data Zone: 2,113,928,704
Last PAA of Data Zone: 48,396,408

BD Disc Information (L2):
Disc ID: VERBAT-IMk-000
Disc Type: BD-R
Disc Size: 120 mm
Disc Class: 1
Disc Version: 2
Number of Layers: 3
Layer Type: Writable
DVD Layer Present: No
CD Layer Present: No
Channel Bit Length: 55.87 nm (33 GB Per Layer)
Push-Pull Polarity: Positive
Recorded Mark Polarity: HTL
BCA Present: Yes
Maximum Transfer Rate: Not Specified
First PAA of Data Zone: 2,702,409,216
Last PAA of Data Zone: 48,393,838

Layer Information:
Layer 0 Sectors: 629,237,088 (1308%)
Layer 1 Sectors: 1,042,113,888 (2167%)
Layer 2 Sectors: 2,671,708,480 (5555%)

 

 

Edited May 15, 2022 by 6000RPM

[dbminter]

Is this the first time you've tried BD XL media?  I know one of the reasons the WH16NS40 is not usable, as far as I'm concerned, is it doesn't properly write to double layer BD media.  9 times out of 10, it writes it incorrectly.

 

[6000RPM]

@dbminter, yes. Verification is successful though, zero errors. Here is the graph:

 

Do note that the disk was written using v1.03 firmware and verified on v1.05. This is Verbatim ~100Gb M-Disc.

[dbminter]

So, you're using 2 WH14NS40 drives?  Writing in a 1.03 firmware drive and verifying in a 1.05 firmware drive?  If that's the case, I'd wait and see if it happens again, but this time use the 1.05 drive to write the BD XL disc.