Jump to content

ImgBurn Support Forum uses cookies. Read the Privacy Policy for more info. To remove this message, please click the button to the right:    I accept the use of cookies

Photo

Xdg3 burn problems


Forum Rules

Read the Guides forum if you don't know how to do something. :readbook:
If you have a question or a problem, check the FAQ and use the Search to see if you can find the answer for yourself. :lightbulb:
If you're having trouble burning double layer media, read Here.
Still stuck? Create a new thread and describe your issue in detail.
Make sure you include a copy of the program's log in your post. No log = :chair:


  • Please log in to reply
21 replies to this topic

#1 supanova

supanova

    ISF Newbie

  • Members
  • Pip
  • 15 posts
  • Location:Nottingham

Posted 10 November 2012 - 06:37 PM

Right in need of help. . . Im using a 524b drive with burnermax fw. Using Mkm003 singapore disc. Config img burn and eeprom settings following the guide . Tried Opc on & off burned at 2.4 & 4 . Buffer set between 80 -512mb burn proof is disabled . Ive tried with smart burn on OHT off HT on & off OSB off. All possible veriations. Ive re installed imgburn. Re installed drivers for drive. Re flashed drive. Etc cleared OPC data every burn then power cycled. And yet my disc STILL Fails. I had x3 different errors
1. Logical unit timed out - invalid write address (most common failior)
2. Bogus drive error dectected (only had once)
3. Burn successful but failed to verify at 44%

Tried this with different ISO files and tired different verb mkm003 discs from diff spindles.

Now the weired thing is the burner is 1 months old burnt 5 disc before with nothing but perferct burns then one day burn failed twice then burnt ok third time round. Then nothing but fails again and occassionally ill get a good burn again.

Also tried burning in safe mode. This is where i get the verification fail error .

Only have one thing left to try and thats to disconnect my other drive in case of conflict but other than that im stumped and possible think the drives defective (burns other media with no problems though)

Will post a few burn logs when im back at home but im sure youve seen these types of errors before to understand which ones.

Any help would be great.

#2 LIGHTNING UK!

LIGHTNING UK!

    Author of ImgBurn

  • Admin
  • PipPipPipPipPip
  • 29,303 posts
  • Gender:Male
  • Location:United Kingdom

Posted 10 November 2012 - 07:39 PM

Mine worked best with OPC off, Force HyperTuning on, Online HyperTuning off, Overspeed off, SmartBurn on and burning at 4x.

Once you've configure the program/drive like that, clear opc history (in the same place as the hypertuning options) and then burn again.

Post a new with that configuration.

The bogus driver error probably means you've got the drive installed on a bad controller. Stick to using the proper Intel one if you have such a thing on your motherboard.
Please don't PM me with questions that should be posted in the forum. I won't reply - Especially if you have post count of 0!!!

Replies to posts belong in the forum where everyone can read them. Please don't PM them.

In fact, don't PM me at all unless it's something I've asked to be told about!

Before asking questions, search the forum to see if someone else already has.

Use the FAQ and Guides forums to your advantage. I don't want to have to tell you to read them!

#3 supanova

supanova

    ISF Newbie

  • Members
  • Pip
  • 15 posts
  • Location:Nottingham

Posted 10 November 2012 - 08:04 PM

Ok will give it ago with the new settings and post log and results later when im home from work.

Could the drive be bad? Or conflicting with other drive??

My comp is controlled by Nvidia chipset which i made sure were upto date. Ill double check that too.

#4 supanova

supanova

    ISF Newbie

  • Members
  • Pip
  • 15 posts
  • Location:Nottingham

Posted 11 November 2012 - 05:01 PM

So after computer decided to go crazy had to restore to earlier stage.Disconnected other drive. Re installed drivers for ihas drive run a lense clearner through (just incase). Re installed imgburn again. Re configured imgburn and eeprom with your settings cleared OPC and power cycled.

And burnt successfully ,verified and got these readings from kprobe2

PI 59 avg 1.43
PIF 3 avg 0.25

So all is well .... Will post back when second burn has done. To see if fixed once n for all.

#5 supanova

supanova

    ISF Newbie

  • Members
  • Pip
  • 15 posts
  • Location:Nottingham

Posted 11 November 2012 - 07:13 PM

Ok second burn done and again successfull.

Results are so so but still burnt with no errors

PI 193 avg 3.69
PIF 6 avg 0.22

Pif only just outside and The PI Highest were at layerbreak. So guessin thats still ok?.

Looks like probem solved ?
Also to mention i noticed burn proof is enabled.

Thanks for advice hope i have no more problems


#6 LIGHTNING UK!

LIGHTNING UK!

    Author of ImgBurn

  • Admin
  • PipPipPipPipPip
  • 29,303 posts
  • Gender:Male
  • Location:United Kingdom

Posted 11 November 2012 - 07:39 PM

Can you post the ImgBurn log and the kprobe graph itself please.

Those values still look a little high to me. Different spindles can produce different results though and even that place that makes the discs can make a difference. The ones from Singapore seem to be the best.
Please don't PM me with questions that should be posted in the forum. I won't reply - Especially if you have post count of 0!!!

Replies to posts belong in the forum where everyone can read them. Please don't PM them.

In fact, don't PM me at all unless it's something I've asked to be told about!

Before asking questions, search the forum to see if someone else already has.

Use the FAQ and Guides forums to your advantage. I don't want to have to tell you to read them!

#7 supanova

supanova

    ISF Newbie

  • Members
  • Pip
  • 15 posts
  • Location:Nottingham

Posted 11 November 2012 - 09:54 PM

Burn 1
I 14:34:34 ImgBurn Version 2.5.7.0 started!
I 14:34:34 Microsoft Windows 7 Ultimate Edition (6.1, Build 7600)
I 14:34:34 Total Physical Memory: 2,095,064 KB - Available: 1,506,084 KB
I 14:34:34 Initialising SPTI...
I 14:34:34 Searching for SCSI / ATAPI devices...
I 14:34:34 -> Drive 1 - Info: ATAPI iHAS524 B AL2A (D:) (ATA)
I 14:34:34 Found 1 DVD±RW/RAM!
I 14:35:18 Operation Started!
I 14:35:18 Source File: C:\Users\Home\Desktop\DISC 1\asscreed3_1.dvd
I 14:35:18 Source File Sectors: 4,267,015 (MODE1/2048)
I 14:35:18 Source File Size: 8,738,846,720 bytes
I 14:35:18 Source File Volume Identifier: DVD_ROM
I 14:35:18 Source File Volume Set Identifier: e2254000MS UDFBridge
I 14:35:18 Source File Application Identifier: CDIMAGE 2.45 (12/06/2000 TM)
I 14:35:18 Source File Implementation Identifier: Microsoft CDIMAGE UDF
I 14:35:19 Source File File System(s): ISO9660, UDF (1.50)
I 14:35:19 Destination Device: [3:1:0] ATAPI iHAS524 B AL2A (D:) (ATA)
I 14:35:19 Destination Media Type: DVD+R DL (Disc ID: MKM-003-00)
I 14:35:19 Destination Media Supported Write Speeds: 2.4x, 4x, 6x, 8x
I 14:35:19 Destination Media Sectors: 4,267,040
I 14:35:19 Write Mode: DVD
I 14:35:19 Write Type: DAO
I 14:35:19 Write Speed: 4x
I 14:35:19 DVD+R DL Reserve Track: No
I 14:35:19 Link Size: Auto
I 14:35:19 Lock Volume: Yes
I 14:35:19 Test Mode: No
I 14:35:19 OPC: No
I 14:35:19 BURN-Proof: Enabled
I 14:35:19 Write Speed Successfully Set! - Effective: 5,540 KB/s (4x)
I 14:35:19 Book Type Setting: DVD-ROM
I 14:35:19 Advanced Settings - Force HT: Yes, Online HT: No, OverSpeed: No, SmartBurn: Yes
I 14:35:19 Optimal L0 Data Zone Capacity: 2,133,520
I 14:35:19 Optimal L0 Data Zone Method: Copied From Original Disc
I 14:35:19 Set L0 Data Zone Capacity Succeeded!
I 14:35:20 Filling Buffer... (512 MB)
I 14:35:27 Writing LeadIn...
I 14:36:00 Writing Session 1 of 1... (1 Track, LBA: 0 - 4267014)
I 14:36:00 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 4267014)
I 14:36:01 Writing Layer 0... (LBA: 0 - 2133519)
I 14:49:13 Writing Layer 1... (LBA: 2133520 - 4267014)
I 15:02:27 Synchronising Cache...
I 15:02:32 Closing Track...
I 15:02:33 Finalising Disc...
I 15:03:07 Exporting Graph Data...
I 15:03:07 Graph Data File: C:\Users\Home\AppData\Roaming\ImgBurn\Graph Data Files\ATAPI_iHAS524_B_AL2A_11-NOVEMBER-2012_14-35_MKM-003-00_4x.ibg
I 15:03:07 Export Successfully Completed!
I 15:03:07 Operation Successfully Completed! - Duration: 00:27:48
I 15:03:07 Average Write Rate: 5,384 KB/s (3.9x) - Maximum Write Rate: 5,801 KB/s (4.2x)
I 15:03:07 Cycling Tray before Verify...
W 15:03:15 Waiting for device to become ready...
I 15:03:29 Device Ready!
I 15:03:30 Operation Started!
I 15:03:30 Source Device: [3:1:0] ATAPI iHAS524 B AL2A (D:) (ATA)
I 15:03:30 Source Media Type: DVD+R DL (Book Type: DVD-ROM) (Disc ID: MKM-003-00)
I 15:03:30 Source Media Supported Write Speeds: 2.4x, 4x, 6x, 8x
I 15:03:30 Image File: C:\Users\Home\Desktop\DISC 1\complex-asscreed3_1.dvd
I 15:03:30 Image File Sectors: 4,267,015 (MODE1/2048)
I 15:03:30 Image File Size: 8,738,846,720 bytes
I 15:03:30 Image File Volume Identifier: DVD_ROM
I 15:03:30 Image File Volume Set Identifier: e2254000MS UDFBridge
I 15:03:30 Image File Application Identifier: CDIMAGE 2.45 (12/06/2000 TM)
I 15:03:30 Image File Implementation Identifier: Microsoft CDIMAGE UDF
I 15:03:30 Image File File System(s): ISO9660, UDF (1.50)
I 15:03:30 Read Speed (Data/Audio): MAX / MAX
I 15:03:31 Verifying Session 1 of 1... (1 Track, LBA: 0 - 4267014)
I 15:03:31 Verifying Track 1 of 1... (MODE1/2048, LBA: 0 - 4267014)
I 15:03:31 Verifying Layer 0... (LBA: 0 - 2133519)
I 15:12:45 Verifying Layer 1... (LBA: 2133520 - 4267014)
I 15:21:57 Exporting Graph Data...
I 15:21:57 Graph Data File: C:\Users\Home\AppData\Roaming\ImgBurn\Graph Data Files\ATAPI_iHAS524_B_AL2A_11-NOVEMBER-2012_14-35_MKM-003-00_4x.ibg
I 15:21:57 Export Successfully Completed!
I 15:21:57 Operation Successfully Completed! - Duration: 00:18:26
I 15:21:57 Average Verify Rate: 7,730 KB/s (5.6x) - Maximum Verify Rate: 11,262 KB/s (8.1x)
I 15:24:18 Close Request Acknowledged
I 15:24:18 Closing Down...
I 15:24:18 Shutting down SPTI...
I 15:24:18 ImgBurn closed!
;

BurnTest.PNG

Burn 2
I 17:23:28 ImgBurn Version 2.5.7.0 started!
I 17:23:28 Microsoft Windows 7 Ultimate Edition (6.1, Build 7600)
I 17:23:28 Total Physical Memory: 2,095,064 KB - Available: 1,464,996 KB
I 17:23:28 Initialising SPTI...
I 17:23:28 Searching for SCSI / ATAPI devices...
I 17:23:28 -> Drive 1 - Info: ATAPI iHAS524 B AL2A (D:) (ATA)
I 17:23:28 Found 1 DVD±RW/RAM!
I 17:23:48 Operation Started!
I 17:23:48 Source File: C:\Users\Home\Desktop\MODwarfighter.dvd
I 17:23:48 Source File Sectors: 4,267,015 (MODE1/2048)
I 17:23:48 Source File Size: 8,738,846,720 bytes
I 17:23:48 Source File Volume Identifier: DVD_ROM
I 17:23:48 Source File Volume Set Identifier: b4b08000MS UDFBridge
I 17:23:48 Source File Application Identifier: CDIMAGE 2.45 (12/06/2000 TM)
I 17:23:48 Source File Implementation Identifier: Microsoft CDIMAGE UDF
I 17:23:48 Source File File System(s): ISO9660, UDF (1.50)
I 17:23:48 Destination Device: [3:1:0] ATAPI iHAS524 B AL2A (D:) (ATA)
I 17:23:48 Destination Media Type: DVD+R DL (Disc ID: MKM-003-00)
I 17:23:49 Destination Media Supported Write Speeds: 2.4x, 4x, 6x, 8x
I 17:23:49 Destination Media Sectors: 4,267,040
I 17:23:49 Write Mode: DVD
I 17:23:49 Write Type: DAO
I 17:23:49 Write Speed: 4x
I 17:23:49 DVD+R DL Reserve Track: No
I 17:23:49 Link Size: Auto
I 17:23:49 Lock Volume: Yes
I 17:23:49 Test Mode: No
I 17:23:49 OPC: No
I 17:23:49 BURN-Proof: Enabled
I 17:23:49 Write Speed Successfully Set! - Effective: 5,540 KB/s (4x)
I 17:23:49 Book Type Setting: DVD-ROM
I 17:23:49 Advanced Settings - Force HT: Yes, Online HT: No, OverSpeed: No, SmartBurn: Yes
I 17:23:49 Optimal L0 Data Zone Capacity: 2,133,520
I 17:23:49 Optimal L0 Data Zone Method: Copied From Original Disc
I 17:23:49 Set L0 Data Zone Capacity Succeeded!
I 17:23:50 Filling Buffer... (512 MB)
I 17:23:57 Writing LeadIn...
I 17:24:29 Writing Session 1 of 1... (1 Track, LBA: 0 - 4267014)
I 17:24:29 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 4267014)
I 17:24:29 Writing Layer 0... (LBA: 0 - 2133519)
I 17:37:42 Writing Layer 1... (LBA: 2133520 - 4267014)
I 17:50:55 Synchronising Cache...
I 17:51:00 Closing Track...
I 17:51:02 Finalising Disc...
I 17:51:35 Exporting Graph Data...
I 17:51:35 Graph Data File: C:\Users\Home\AppData\Roaming\ImgBurn\Graph Data Files\ATAPI_iHAS524_B_AL2A_11-NOVEMBER-2012_17-23_MKM-003-00_4x.ibg
I 17:51:35 Export Successfully Completed!
I 17:51:35 Operation Successfully Completed! - Duration: 00:27:46
I 17:51:35 Average Write Rate: 5,384 KB/s (3.9x) - Maximum Write Rate: 5,634 KB/s (4.1x)
I 17:51:35 Cycling Tray before Verify...
W 17:51:42 Waiting for device to become ready...
I 17:51:58 Device Ready!
I 17:51:58 Operation Started!
I 17:51:58 Source Device: [3:1:0] ATAPI iHAS524 B AL2A (D:) (ATA)
I 17:51:58 Source Media Type: DVD+R DL (Book Type: DVD-ROM) (Disc ID: MKM-003-00)
I 17:51:58 Source Media Supported Write Speeds: 2.4x, 4x, 6x, 8x
I 17:51:58 Image File: C:\Users\Home\Desktop\MODwarfighter.dvd
I 17:51:58 Image File Sectors: 4,267,015 (MODE1/2048)
I 17:51:58 Image File Size: 8,738,846,720 bytes
I 17:51:58 Image File Volume Identifier: DVD_ROM
I 17:51:58 Image File Volume Set Identifier: b4b08000MS UDFBridge
I 17:51:58 Image File Application Identifier: CDIMAGE 2.45 (12/06/2000 TM)
I 17:51:58 Image File Implementation Identifier: Microsoft CDIMAGE UDF
I 17:51:58 Image File File System(s): ISO9660, UDF (1.50)
I 17:51:58 Read Speed (Data/Audio): MAX / MAX
I 17:52:00 Verifying Session 1 of 1... (1 Track, LBA: 0 - 4267014)
I 17:52:00 Verifying Track 1 of 1... (MODE1/2048, LBA: 0 - 4267014)
I 17:52:00 Verifying Layer 0... (LBA: 0 - 2133519)
I 18:01:13 Verifying Layer 1... (LBA: 2133520 - 4267014)
I 18:10:26 Exporting Graph Data...
I 18:10:26 Graph Data File: C:\Users\Home\AppData\Roaming\ImgBurn\Graph Data Files\ATAPI_iHAS524_B_AL2A_11-NOVEMBER-2012_17-23_MKM-003-00_4x.ibg
I 18:10:26 Export Successfully Completed!
I 18:10:26 Operation Successfully Completed! - Duration: 00:18:26
I 18:10:26 Average Verify Rate: 7,730 KB/s (5.6x) - Maximum Verify Rate: 11,262 KB/s (8.1x)

PI log.PNG

When i brought these discs i brought x2 packs of 10 mkm003 discs (Verb code 43666) Singapore right ??? thats what they were advertised as.

Edited by supanova, 11 November 2012 - 10:06 PM.


#8 LIGHTNING UK!

LIGHTNING UK!

    Author of ImgBurn

  • Admin
  • PipPipPipPipPip
  • 29,303 posts
  • Gender:Male
  • Location:United Kingdom

Posted 11 November 2012 - 10:10 PM

I've had them with the little higher error rate section at the start like that, but yours seem to be a bit rough around the outer edge of the disc (the layer break point and where it does the 'overburning'). It does vary from spindle to spindle (I usually buy from a few different places).

All of this stuff (burn quality etc) is at a level beyond where software has any control or say in the matter, but you might want to go for another clear of the opc history before trying your next one.

I've also seen flashing back to the standard firmware (resets something in the eeprom I think) and then putting the modified one back on again can help. Just don't forget to then double check the drive/eeprom hypertuning etc options again before making yet another burn :)
Please don't PM me with questions that should be posted in the forum. I won't reply - Especially if you have post count of 0!!!

Replies to posts belong in the forum where everyone can read them. Please don't PM them.

In fact, don't PM me at all unless it's something I've asked to be told about!

Before asking questions, search the forum to see if someone else already has.

Use the FAQ and Guides forums to your advantage. I don't want to have to tell you to read them!

#9 supanova

supanova

    ISF Newbie

  • Members
  • Pip
  • 15 posts
  • Location:Nottingham

Posted 11 November 2012 - 10:19 PM

The disc i got were from Ebay. Always following the rule of clearing the OPC and a power cycle before a burn. As for settings i'll stick with whats working untill problems arise. Im not one for online gaming so guessing the PI & PIF Providing within tollerence should be fine?

But for now im hoping thats the last of the errors for now. Thanks for your help n advice :thumbup:

Edited by supanova, 11 November 2012 - 10:20 PM.


#10 LIGHTNING UK!

LIGHTNING UK!

    Author of ImgBurn

  • Admin
  • PipPipPipPipPip
  • 29,303 posts
  • Gender:Male
  • Location:United Kingdom

Posted 11 November 2012 - 10:40 PM

You don't need to clear opc each time, just the once.

After configuring the drive's eeprom with the settings I told you, I didn't touch anything and just kept getting good burns after that.

Take a look at this post in a thread where I did 12 burns in a row from the same spindle.

http://forum.imgburn.com/index.php?showtopic=18871&st=0&p=136519&#entry136519
Please don't PM me with questions that should be posted in the forum. I won't reply - Especially if you have post count of 0!!!

Replies to posts belong in the forum where everyone can read them. Please don't PM them.

In fact, don't PM me at all unless it's something I've asked to be told about!

Before asking questions, search the forum to see if someone else already has.

Use the FAQ and Guides forums to your advantage. I don't want to have to tell you to read them!

#11 supanova

supanova

    ISF Newbie

  • Members
  • Pip
  • 15 posts
  • Location:Nottingham

Posted 12 November 2012 - 09:27 AM

I noticed you got this error
Reason: L-EC Uncorrectable Error E
16:58:12 Failed to Read Sector 2086912
- Reason: L-EC Uncorrectable Error E
16:58:12 Failed to Verify Sectors!
16:58:14 Exporting Graph Data...
16:58:14 Graph Data File: C:\Users\Richard\AppData\Roaming\ImgBurn\ Graph Data Files\ATAPI_iHAS124_B_AL0S_21- OCTOBER-2011_16-03_CMC_MAG-D01- 00_2.4x.ibg
I 16:58:14 Export Successfully Completed! E
16:58:14 Operation Failed! - Duration: 00:09:34

This is the same i got on the verification. Any idea what causes this?

I didnt know that u didnt have to clear OPC everytime many forums suggest this


#12 supanova

supanova

    ISF Newbie

  • Members
  • Pip
  • 15 posts
  • Location:Nottingham

Posted 12 November 2012 - 09:29 AM

After your 12 burns did you continue to burn without any changes or just a clear of OPC?

#13 LIGHTNING UK!

LIGHTNING UK!

    Author of ImgBurn

  • Admin
  • PipPipPipPipPip
  • 29,303 posts
  • Gender:Male
  • Location:United Kingdom

Posted 12 November 2012 - 11:56 AM

What causes it is the drive doing a bad job of burning the discs ('CMC MAG-D01-00' MID/dye in that specific case). It burnt it and then couldn't read it back.

It took something like 7 burns to find settings that just kept working. Once I'd found them, I didn't do / touch anything and each disc just came out fine.
Please don't PM me with questions that should be posted in the forum. I won't reply - Especially if you have post count of 0!!!

Replies to posts belong in the forum where everyone can read them. Please don't PM them.

In fact, don't PM me at all unless it's something I've asked to be told about!

Before asking questions, search the forum to see if someone else already has.

Use the FAQ and Guides forums to your advantage. I don't want to have to tell you to read them!

#14 supanova

supanova

    ISF Newbie

  • Members
  • Pip
  • 15 posts
  • Location:Nottingham

Posted 12 November 2012 - 01:24 PM

Right so it wasnt anything to do with poor settings just a bad write. I have a few others lined up ready for burning will see how those turn out and post them results up also.

#15 LIGHTNING UK!

LIGHTNING UK!

    Author of ImgBurn

  • Admin
  • PipPipPipPipPip
  • 29,303 posts
  • Gender:Male
  • Location:United Kingdom

Posted 12 November 2012 - 01:28 PM

Settings don't really give you bad burns, there's nothing the program itself can do to make them better/worse as burning is controlled 100% by the drive. The firmware / chipset in the drive are what deals with all of that stuff.
Please don't PM me with questions that should be posted in the forum. I won't reply - Especially if you have post count of 0!!!

Replies to posts belong in the forum where everyone can read them. Please don't PM them.

In fact, don't PM me at all unless it's something I've asked to be told about!

Before asking questions, search the forum to see if someone else already has.

Use the FAQ and Guides forums to your advantage. I don't want to have to tell you to read them!

#16 supanova

supanova

    ISF Newbie

  • Members
  • Pip
  • 15 posts
  • Location:Nottingham

Posted 13 November 2012 - 08:22 PM

So Here is the result from the next burn.

I 18:37:36 ImgBurn Version 2.5.7.0 started!
I 18:37:36 Microsoft Windows 7 Ultimate Edition (6.1, Build 7600)
I 18:37:36 Total Physical Memory: 2,095,064 KB - Available: 1,517,176 KB
I 18:37:36 Initialising SPTI...
I 18:37:36 Searching for SCSI / ATAPI devices...
I 18:37:36 -> Drive 1 - Info: ATAPI iHAS524 B AL2A (D:) (ATA)
I 18:37:36 Found 1 DVD±RW/RAM!
I 18:39:45 Operation Started!
I 18:39:45 Source File: C:\Users\Home\Desktop\Hitman Bloodmoney.dvd
I 18:39:45 Source File Sectors: 4,267,015 (MODE1/2048)
I 18:39:45 Source File Size: 8,738,846,720 bytes
I 18:39:45 Source File Volume Identifier: DVD_ROM
I 18:39:45 Source File Volume Set Identifier: 7fe8000
I 18:39:45 Source File Application Identifier: CDIMAGE 2.45 (12/06/2000 TM)
I 18:39:45 Source File Implementation Identifier: Microsoft CDIMAGE UDF
I 18:39:45 Source File File System(s): ISO9660, UDF (1.50)
I 18:39:45 Destination Device: [3:1:0] ATAPI iHAS524 B AL2A (D:) (ATA)
I 18:39:45 Destination Media Type: DVD+R DL (Disc ID: MKM-003-00)
I 18:39:45 Destination Media Supported Write Speeds: 2.4x, 4x, 6x, 8x
I 18:39:45 Destination Media Sectors: 4,267,040
I 18:39:46 Write Mode: DVD
I 18:39:46 Write Type: DAO
I 18:39:46 Write Speed: 4x
I 18:39:46 DVD+R DL Reserve Track: No
I 18:39:46 Link Size: Auto
I 18:39:46 Lock Volume: Yes
I 18:39:46 Test Mode: No
I 18:39:46 OPC: No
I 18:39:46 BURN-Proof: Enabled
I 18:39:46 Write Speed Successfully Set! - Effective: 5,540 KB/s (4x)
I 18:39:46 Book Type Setting: DVD-ROM
I 18:39:46 Advanced Settings - Force HT: Yes, Online HT: No, OverSpeed: No, SmartBurn: Yes
I 18:39:46 Optimal L0 Data Zone Capacity: 2,133,520
I 18:39:46 Optimal L0 Data Zone Method: Copied From Original Disc
I 18:39:46 Set L0 Data Zone Capacity Succeeded!
I 18:39:47 Filling Buffer... (512 MB)
I 18:39:54 Writing LeadIn...
I 18:40:27 Writing Session 1 of 1... (1 Track, LBA: 0 - 4267014)
I 18:40:27 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 4267014)
I 18:40:27 Writing Layer 0... (LBA: 0 - 2133519)
I 18:53:40 Writing Layer 1... (LBA: 2133520 - 4267014)
I 19:06:53 Synchronising Cache...
I 19:07:07 Closing Track...
I 19:07:08 Finalising Disc...
I 19:07:42 Exporting Graph Data...
I 19:07:42 Graph Data File: C:\Users\Home\AppData\Roaming\ImgBurn\Graph Data Files\ATAPI_iHAS524_B_AL2A_13-NOVEMBER-2012_18-39_MKM-003-00_4x.ibg
I 19:07:42 Export Successfully Completed!
I 19:07:42 Operation Successfully Completed! - Duration: 00:27:56
I 19:07:42 Average Write Rate: 5,380 KB/s (3.9x) - Maximum Write Rate: 5,634 KB/s (4.1x)
I 19:07:42 Cycling Tray before Verify...
W 19:07:50 Waiting for device to become ready...
I 19:08:05 Device Ready!
I 19:08:05 Operation Started!
I 19:08:05 Source Device: [3:1:0] ATAPI iHAS524 B AL2A (D:) (ATA)
I 19:08:05 Source Media Type: DVD+R DL (Book Type: DVD-ROM) (Disc ID: MKM-003-00)
I 19:08:05 Source Media Supported Write Speeds: 2.4x, 4x, 6x, 8x
I 19:08:05 Image File: C:\Users\Home\Desktop\Hitman Bloodmoney.dvd
I 19:08:05 Image File Sectors: 4,267,015 (MODE1/2048)
I 19:08:05 Image File Size: 8,738,846,720 bytes
I 19:08:06 Image File Volume Identifier: DVD_ROM
I 19:08:06 Image File Volume Set Identifier: 7fe8000
I 19:08:06 Image File Application Identifier: CDIMAGE 2.45 (12/06/2000 TM)
I 19:08:06 Image File Implementation Identifier: Microsoft CDIMAGE UDF
I 19:08:06 Image File File System(s): ISO9660, UDF (1.50)
I 19:08:06 Read Speed (Data/Audio): MAX / MAX
I 19:08:07 Verifying Session 1 of 1... (1 Track, LBA: 0 - 4267014)
I 19:08:07 Verifying Track 1 of 1... (MODE1/2048, LBA: 0 - 4267014)
I 19:08:07 Verifying Layer 0... (LBA: 0 - 2133519)
I 19:17:20 Verifying Layer 1... (LBA: 2133520 - 4267014)
I 19:26:33 Exporting Graph Data...
I 19:26:33 Graph Data File: C:\Users\Home\AppData\Roaming\ImgBurn\Graph Data Files\ATAPI_iHAS524_B_AL2A_13-NOVEMBER-2012_18-39_MKM-003-00_4x.ibg
I 19:26:33 Export Successfully Completed!
I 19:26:33 Operation Successfully Completed! - Duration: 00:18:26
I 19:26:33 Average Verify Rate: 7,730 KB/s (5.6x) - Maximum Verify Rate: 11,256 KB/s (8.1x)

PI Results.PNG

Well The results peaked at layer break, abit of a spike at start guessing this is ok very simiar to previous burns. What you think? Any suggestion of tweaks to better these results further?

#17 LIGHTNING UK!

LIGHTNING UK!

    Author of ImgBurn

  • Admin
  • PipPipPipPipPip
  • 29,303 posts
  • Gender:Male
  • Location:United Kingdom

Posted 13 November 2012 - 08:28 PM

Have you done what I said about flashing back to the official LiteOn firmware and then putting the modified one back on again?

After that I'd just try buying another spindle of 10 discs from elsewhere.
Please don't PM me with questions that should be posted in the forum. I won't reply - Especially if you have post count of 0!!!

Replies to posts belong in the forum where everyone can read them. Please don't PM them.

In fact, don't PM me at all unless it's something I've asked to be told about!

Before asking questions, search the forum to see if someone else already has.

Use the FAQ and Guides forums to your advantage. I don't want to have to tell you to read them!

#18 supanova

supanova

    ISF Newbie

  • Members
  • Pip
  • 15 posts
  • Location:Nottingham

Posted 13 November 2012 - 08:35 PM

yea flashed back to org then back to modified fw seems to be the same. When these discs runs out ill get some more from else where any suggestions to get the mkm003?

I re went over those logs of yours in the settings you have a device buffer of 40mb (only difference between our settings ??) But you got pretty good results. Would it make much of a difference if mines set to the 512mb?

#19 LIGHTNING UK!

LIGHTNING UK!

    Author of ImgBurn

  • Admin
  • PipPipPipPipPip
  • 29,303 posts
  • Gender:Male
  • Location:United Kingdom

Posted 13 November 2012 - 08:52 PM

The buffer makes no difference.... like most of the settings people go on about changing in order to improve burn quality. By giving the app more for a write buffer (which it probably won't make use of) you're simply taking it away from the rest of the machine/software.

They don't seem to realise that the drive handles all this stuff internally. It doesn't matter what OS/software you're running, how much buffer you give the program, or even which computer the drive is attached to... the burn quality will always be the same (assuming it has enough of everything to reach its full potential that is).

Burn quality comes from your drive/firmware/media combo.
Please don't PM me with questions that should be posted in the forum. I won't reply - Especially if you have post count of 0!!!

Replies to posts belong in the forum where everyone can read them. Please don't PM them.

In fact, don't PM me at all unless it's something I've asked to be told about!

Before asking questions, search the forum to see if someone else already has.

Use the FAQ and Guides forums to your advantage. I don't want to have to tell you to read them!

#20 supanova

supanova

    ISF Newbie

  • Members
  • Pip
  • 15 posts
  • Location:Nottingham

Posted 13 November 2012 - 08:59 PM

So in theroy someone who has same drive with same firmware using the same discs (from same spindle) Like burning same media etc would have similar to almost identical results ?




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users