Ebang Posted May 19, 2009 Posted May 19, 2009 (edited) I have burned 10-20 DVD9s in 'build' mode using an external DVD burner , marked as device "[0:0:0] HL-DT-ST DVDRAM GE20LU10 FE06 (K:) USB". Every time I burn a DVD9 in 'build' mode I get an error about L0 data zone capacity miscompare. I'm using Verbatim media which I'm also using on a different computer with an internal burner and I've never had any issues there. I have not noticed any issues with playing the discs but I am getting a little nervous about the warning. Sample log is enclosed. I think the log shows all of the steps I'm doing, including the fact that I am selecting a layer-break position from the options that ImgBurn offers. This is what appears to be later flagged as 'miscompare' and readjusted. I'd be very grateful if someone can explain to me what is causing the warning and what can I do to address the problem. Thanks. I 14:11:49 ImgBurn Version 2.3.2.0 started!I 14:11:49 Microsoft Windows XP Professional (5.1, Build 2600 : Service Pack 3)I 14:11:49 Total Physical Memory: 3,659,668 KB - Available: 3,020,324 KBW 14:11:49 Drive I:\ (FAT32) does not support single files > 4 GB in size.I 14:11:49 Initialising SPTI...I 14:11:49 Searching for SCSI / ATAPI devices...I 14:11:50 Found 2 DVD-ROMs and 2 DVD Edited May 19, 2009 by Ebang
LIGHTNING UK! Posted May 19, 2009 Posted May 19, 2009 Update ImgBurn and try again. Oh and it's good practice to never ask for help with old versions of programs. Update, see if it still happens AND THEN report your problem.
Ebang Posted May 19, 2009 Author Posted May 19, 2009 (edited) Oops. Thanks for the quick response. I will upgrade to the current version and report back. Edited May 20, 2009 by Ebang
Ebang Posted May 20, 2009 Author Posted May 20, 2009 Downloaded and installed the current version and burned my first DVD9 - and the problem persists. Log included below. I 19:30:34 ImgBurn Version 2.4.4.0 started!I 19:30:34 Microsoft Windows XP Professional (5.1, Build 2600 : Service Pack 3)I 19:30:34 Total Physical Memory: 3,659,668 KB - Available: 2,981,572 KBW 19:30:34 Drive I:\ (FAT32) does not support single files > 4 GB in size.W 19:30:34 AnyDVD can interfere with ImgBurn's ability to verify accurately, please ensure it's disabled!I 19:30:34 Initialising SPTI...I 19:30:34 Searching for SCSI / ATAPI devices...I 19:30:35 Found 2 DVD-ROMs and 2 DVD
blutach Posted May 20, 2009 Posted May 20, 2009 W 19:30:34 AnyDVD can interfere with ImgBurn's ability to verify accurately, please ensure it's disabled! Considered doing this? As for your L0 miscompare - reset your default settings. Regards
LIGHTNING UK! Posted May 20, 2009 Posted May 20, 2009 Put that disc back in the drive and copy + paste the disc info from the panel on the right.
Ebang Posted May 20, 2009 Author Posted May 20, 2009 Put that disc back in the drive and copy + paste the disc info from the panel on the right. Shown below. Interestingly, it shows the original L0 Data Zone Capacity of 1,940,048 . I'll let LUK interpret what that means. Also, in response to Blutach, I keep AnyDVD disabled except when needed. It has positively been disabled for the past few days. HL-DT-ST DVDRAM GE20LU10 FE06 (USB)Current Profile: DVD+R DL Disc Information:Status: CompleteErasable: NoSessions: 1Sectors: 3,828,352Size: 7,840,464,896 bytesTime: 850:46:52 (MM:SS:FF)Supported Write Speeds: 2.4x, 4x DVD
LIGHTNING UK! Posted May 20, 2009 Posted May 20, 2009 Ok so at least the LB was moved eventually, even if the drive didn't report it as such the first time around. You'd be helping me out if the next time you burn a DL disc you press F8 before clicking the big 'Write' button. That'll put more info into the log and it might just enable me to tweak my code incase I need to wait a bit for the drive to set the LB position and it's not returning the error codes that make the current version of ImgBurn wait.
Recommended Posts