philbilldick Posted August 10, 2009 Share Posted August 10, 2009 Have installed 2.5.0.0 and are now unable to cut Verbatim 8x DVD+R DL discs when I load them I get either disk not empty or disc drive just keeps on going with 2.4.4.0 I had no problems at all using HT-DT-DT DVD+-RW GSA H31N works on all types of single layer. Have I missed a trick on any settings Be grateful for any advice Regards Phil Link to comment Share on other sites More sharing options...
spinningwheel Posted August 10, 2009 Share Posted August 10, 2009 philbilldick; Post a log from your failed burn please. Link to comment Share on other sites More sharing options...
philbilldick Posted August 10, 2009 Author Share Posted August 10, 2009 philbilldick; Post a log from your failed burn please. Sorry, should have done that before. Log is I 15:16:37 ImgBurn Version 2.5.0.0 started! I 15:16:37 Microsoft Windows XP Professional (5.1, Build 2600 : Service Pack 3) I 15:16:37 Total Physical Memory: 3,143,520 KB - Available: 2,493,748 KB I 15:16:37 Initialising SPTI... I 15:16:37 Searching for SCSI / ATAPI devices... I 15:16:38 Found 1 DVD-ROM and 1 DVD Link to comment Share on other sites More sharing options...
philbilldick Posted August 10, 2009 Author Share Posted August 10, 2009 Have just noticed a msg flashes on screen then disappears. Have ImbBurn running for a BUILD, no disc inserted Here is full msg response Device Not Ready(Medium Not Present) (insert disc) Device Not Ready(Logical Unit Is In Process of Becoming Ready) (flash msg) Device Not Ready(Not Ready to Ready Change - Medium May Have Changed) (then get) Didk Not Empty Don't know if this helps Regards Phil Link to comment Share on other sites More sharing options...
mmalves Posted August 10, 2009 Share Posted August 10, 2009 With the disc in the drive, please post the text shown in the Device tab of ImgBurn's Build mode. Link to comment Share on other sites More sharing options...
philbilldick Posted August 11, 2009 Author Share Posted August 11, 2009 With the disc in the drive, please post the text shown in the Device tab of ImgBurn's Build mode. Device text HL-DT-ST DVD+-RW GSA-H31N B106 (ATAPI) Current Profile: DVD+RW Disc Information: Status: Unknown Erasable: Unknown Formatted: Unknown Sessions: Unknown Sectors: 2,295,104 Size: 4,700,372,992 bytes Time: 510:03:29 (MM:SS:FF) Supported Write Speeds: 2.4x TOC Information: Session 1... (LBA: 0) -> Track 01 (Mode 1, LBA: 0 - 2295103) -> LeadOut (LBA: 2295104) Physical Format Information (Last Recorded): Disc ID: MCC-004-00 Book Type: DVD+R Part Version: 1 Disc Size: 120mm Maximum Read Rate: Not Specified Number of Layers: 1 Track Path: Parallel Track Path (PTP) Linear Density: 0.267 um/bit Track Density: 0.74 um/track First Physical Sector of Data Area: 196,608 Last Physical Sector of Data Area: 2,491,711 Last Physical Sector in Layer 0: 0 Performance (Write Speeds): Descriptor 1... -> B0: 0x00, B1: 0x00, B2: 0x00, B3: 0x00 -> EL: 2295103 (0x0023053F) -> RS: 11,080 KB/s (8x) - WS: 3,324 KB/s (2.4x) Regards Phil Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted August 11, 2009 Share Posted August 11, 2009 If that Disc ID is correct, it's not a DL disc. Either way, your drive is returning bogus info for the media. It's saying 'Unknown' for stuff it should easily support and reporting the wrong 'Current Profile' for it too. Link to comment Share on other sites More sharing options...
mmalves Posted August 11, 2009 Share Posted August 11, 2009 HL-DT-ST DVD+-RW GSA-H31N B106 (ATAPI) Update your burner's firmware (remove any disc and close the tray before updating then reboot after it's finished). Does it help with your problem? If you can please post the Information again Link to comment Share on other sites More sharing options...
philbilldick Posted August 11, 2009 Author Share Posted August 11, 2009 If that Disc ID is correct, it's not a DL disc. Either way, your drive is returning bogus info for the media. It's saying 'Unknown' for stuff it should easily support and reporting the wrong 'Current Profile' for it too. I have gone thru the remaning discs on my tub. 2 were OK now 1 shows Disc Not Empty & 1 shows Device Not Ready(Medium Not Present) 1 showed Device Not Ready(Logical Unit becoming ready) - but never did anything else 8 showed Disc Not Empty 4 showed Device Not Ready(Medium Not Present) Do I assume all these are duff? or does the drive need a clean? Link to comment Share on other sites More sharing options...
philbilldick Posted August 11, 2009 Author Share Posted August 11, 2009 HL-DT-ST DVD+-RW GSA-H31N B106 (ATAPI) Update your burner's firmware (remove any disc and close the tray before updating then reboot after it's finished). Does it help with your problem? If you can please post the Information again OK have updated firmware and rebooted. First disc in showed Disc Not Empty Second disc showed Ready - Device Tab text below All others so far are either Disc Not Empty or Device Not Ready(Medium Not Present) HL-DT-ST DVD+-RW GSA-H31N B110 (ATAPI) Current Profile: DVD+R DL Disc Information: Status: Empty Erasable: No Free Sectors: 4,173,824 Free Space: 8,547,991,552 bytes Free Time: 927:32:74 (MM:SS:FF) Supported Write Speeds: 4x, 6x, 8x DVD Link to comment Share on other sites More sharing options...
philbilldick Posted August 11, 2009 Author Share Posted August 11, 2009 HL-DT-ST DVD+-RW GSA-H31N B106 (ATAPI) Update your burner's firmware (remove any disc and close the tray before updating then reboot after it's finished). Does it help with your problem? If you can please post the Information again Below is Device Tab text for Disc Not Empty HL-DT-ST DVD+-RW GSA-H31N B110 (ATAPI) Current Profile: DVD+RW Disc Information: Status: Unknown Erasable: Unknown Formatted: Unknown Sessions: Unknown Sectors: 16,384,000 Size: 33,554,432,000 bytes Time: 3640:55:25 (MM:SS:FF) Supported Write Speeds: 2.4x TOC Information: Session 1... (LBA: 0) -> Track 01 (Mode 1, LBA: 0 - 16383999) -> LeadOut (LBA: 16384000) Physical Format Information (Last Recorded): Disc ID: MKM-003-00 Book Type: DVD+R DL Part Version: 1 Disc Size: 120mm Maximum Read Rate: Not Specified Number of Layers: 2 Track Path: Opposite Track Path (OTP) Linear Density: 0.293 um/bit Track Density: 0.74 um/track First Physical Sector of Data Area: 196,608 Last Physical Sector of Data Area: 16,580,607 Last Physical Sector in Layer 0: 2,283,519 Performance (Write Speeds): Descriptor 1... -> B0: 0x00, B1: 0x00, B2: 0x00, B3: 0x00 -> EL: 16383999 (0x00F9FFFF) -> RS: 11,080 KB/s (8x) - WS: 3,324 KB/s (2.4x) Link to comment Share on other sites More sharing options...
mmalves Posted August 11, 2009 Share Posted August 11, 2009 You could try a lens cleaning disc just for kicks, but I think your burner is defective and needs replacement Link to comment Share on other sites More sharing options...
philbilldick Posted August 11, 2009 Author Share Posted August 11, 2009 You could try a lens cleaning disc just for kicks, but I think your burner is defective and needs replacement Will get a lens cleaning kit and see what happens. Can I get a copy of 2.4.4.0 from you and see if the writer is still giving same problems. (It all seemed to be working fine until I installed 2.5.0.0) Regards Phil Link to comment Share on other sites More sharing options...
mmalves Posted August 11, 2009 Share Posted August 11, 2009 We don't support versions before 2.5.0.0 ImgBurn shows what the burner reports and this hasn't changed in the new version. Link to comment Share on other sites More sharing options...
Recommended Posts