The Incredible Bulk Posted August 18, 2006 Share Posted August 18, 2006 I'm new to this so I'm still learning and here is my problem. I am using DVD Shrink 3.1 to rip a DVD and ImgBurn 2.0.0 to burn it on a SONY DVD RW DRU-820A 2.0c. First off, I can't even get it to consider burning to a DVD-R. Here is the error message I keep getting: I/O Error! Device [0:0:0] SONY DVD RW DRU-820A 2.0c (USB) ScsiStatus: 0x02 Interpretation: Check Condition CDB: 2A 00 00 00 00 00 00 00 20 00 Interpretation: Write (10) - Sectors: 0-31 Sense Area: 70 00 03 00 00 00 00 0A 00 00 81 00 73 03 00 00 00 00 Interpretation: Power Calibration Error Second, I tried using a DVD-RAM instead and it went through the entire writing processto 100%, only to give an error at the end and produce a DVD that read as "UNFORMAT" on my Panasonic DMR E85H DVD recorder/player. Any help would be much appreciated. Thanks. Link to comment Share on other sites More sharing options...
blutach Posted August 18, 2006 Share Posted August 18, 2006 I'm hoping we can see the full log please? But check firmware, media quality, DMA and burn speed (especially on a USB). And welcome to ImgBurn Forum!! Regards Link to comment Share on other sites More sharing options...
The Incredible Bulk Posted August 22, 2006 Author Share Posted August 22, 2006 Thanks for the quick response, sorry for the slow response. Here is my log: I 01:31:37 ImgBurn Version 2.0.0.0 started! I 01:31:38 Microsoft Windows XP Professional (5.1, Build 2600 : Service Pack 2) W 01:31:38 Drive C:\ (FAT32) does not support single files > 4 GB I 01:31:38 Initialising SPTI... I 01:31:38 Searching for SCSI / ATAPI devices... I 01:31:39 Found 1 CD-ROM and 1 DVD?RW/RAM! I 01:31:51 Operation Started! I 01:31:51 Source File: D:\BLADE_TRINITY_EXTENDED.ISO I 01:31:51 Source File Sectors: 2,109,031 (MODE1/2048) I 01:31:51 Source File Size: 4,319,295,488 bytes I 01:31:51 Source File Volume Identifier: BLADE_TRINITY_EXTENDED I 01:31:52 Source File Implementation Identifier: DVD Shrink I 01:31:52 Source File File System(s): ISO9660, UDF (1.02) I 01:31:52 Destination Device: [0:0:0] SONY DVD RW DRU-820A 2.0c (G:) (USB) I 01:31:52 Destination Media Type: DVD-RAM (Disc ID: Matsushita Electric Industrial CO.,LTD. M01J3003) (Speeds: 3x) I 01:31:52 Destination Media Sectors: 2,236,704 I 01:31:52 Write Mode: DVD I 01:31:52 Write Type: DAO I 01:31:52 Write Speed: MAX I 01:31:52 Link Size: Auto I 01:31:52 Test Mode: No I 01:31:52 BURN-Proof: Enabled I 01:31:53 Filling Buffer... I 01:31:54 Writing LeadIn... I 01:31:56 Writing Image... I 02:12:09 Synchronising Cache... I 02:12:11 Image MD5: 73393b501028441ba83e0d4cf24b8886 I 02:12:12 Operation Successfully Completed! - Duration: 00:40:19 I 02:12:12 Average Write Rate: 1,748 KB/s (1.3x) - Maximum Write Rate: 2,099 KB/s (1.5x) I 02:12:12 Cycling Tray before Verify... W 02:12:25 Waiting for device to become ready... I 02:12:46 Device Ready! I 02:12:46 Operation Started! I 02:12:46 Source Device: [0:0:0] SONY DVD RW DRU-820A 2.0c (G:) (USB) I 02:12:46 Source Media Type: DVD-RAM (Book Type: DVD-RAM) (Disc ID: Matsushita Electric Industrial CO.,LTD. M01J3003) (Speeds: 3x) I 02:12:46 Image File: D:\BLADE_TRINITY_EXTENDED.ISO I 02:12:46 Image File Sectors: 2,109,031 (MODE1/2048) I 02:12:46 Image File Size: 4,319,295,488 bytes I 02:12:46 Image File Volume Identifier: BLADE_TRINITY_EXTENDED I 02:12:46 Image File Implementation Identifier: DVD Shrink I 02:12:46 Image File File System(s): ISO9660, UDF (1.02) I 02:12:47 Verifying Sectors... I 02:23:16 Device MD5: 73393b501028441ba83e0d4cf24b8886 I 02:23:16 Image MD5: 73393b501028441ba83e0d4cf24b8886 I 02:23:17 Operation Successfully Completed! - Duration: 00:10:30 I 02:23:17 Average Verify Rate: 6,705 KB/s (4.8x) - Maximum Verify Rate: 6,984 KB/s (5.0x) Now the problem I'm running into is that after it goes through this entire process and I put the DVD into my Panasonic DMR-E85H, it reads "UNFORMAT" on the face of the player and it says on-screen that the disc is not properly formatted. What I had done prior to all this was use DVD Shrink 3.1 and selected the target device as an ISO Disc Image instead of a Hard Disk Folder. Which is more effective? Which is the better option? If I could get a quick step-by-step, it would be greatly appreciated. Thanks again. Link to comment Share on other sites More sharing options...
The Incredible Bulk Posted August 22, 2006 Author Share Posted August 22, 2006 Also, I forgot to add that I had to use the "custom compress" feature to make sure that I could fit it on a Panasonic 4.7 GB DVD-RAM and I made it as small as possible. Could this be part of the problem? Link to comment Share on other sites More sharing options...
cornholio7 Posted August 22, 2006 Share Posted August 22, 2006 what speed were you trying to write to the dvd-r ? Link to comment Share on other sites More sharing options...
The Incredible Bulk Posted August 22, 2006 Author Share Posted August 22, 2006 what speed were you trying to write to the dvd-r ? I had the write speed set to the default which was MAX. Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted August 22, 2006 Share Posted August 22, 2006 I'm not sure DVDRAM will work the same way a normal DVD-R or DVD+R would do. The player may try to read the disc in the true DVDRAM way and not as if it's a DVD Video disc. (Sorry for being a bit vague, I don't have any real experience with standalones / dvdram etc). Your original power calibration error is due to a hardware/firmware/media mismatch. Assuming your firmware is up to date, you need to source some discs that your drive supports properly. The easiest way to do that is to find someone else with that drive, who is getting decent result. As such I would recommend you pay the cdfreaks forum a visit. They have forums for most makes of drives. Basically though, you should look to buy some discs using the MCC or TY (Taiyo Yuden) dyes. Link to comment Share on other sites More sharing options...
The Incredible Bulk Posted August 22, 2006 Author Share Posted August 22, 2006 I'm not sure DVDRAM will work the same way a normal DVD-R or DVD+R would do. The player may try to read the disc in the true DVDRAM way and not as if it's a DVD Video disc. (Sorry for being a bit vague, I don't have any real experience with standalones / dvdram etc). Your original power calibration error is due to a hardware/firmware/media mismatch. Assuming your firmware is up to date, you need to source some discs that your drive supports properly. The easiest way to do that is to find someone else with that drive, who is getting decent result. As such I would recommend you pay the cdfreaks forum a visit. They have forums for most makes of drives. Basically though, you should look to buy some discs using the MCC or TY (Taiyo Yuden) dyes. When I try to use a DVD-R, this is the error message I get: DeviceIoControl (FSCTL_LOCK_VOLUME) Failed! Unable to lock volume for exclusive access Reason: Access is denied Options [CANCEL] [TRY AGAIN] [CONTINUE] After I press CONTINUE, I get the error message from the first post above, which is why I switched over to DVD-RAM. It will at least take me to the end of the process, even if the product seems to be unusable. Link to comment Share on other sites More sharing options...
cornholio7 Posted August 23, 2006 Share Posted August 23, 2006 http://forum.imgburn.com/index.php?s=&...dpost&p=975 then check this out and check your DMA too also on the same page (post#3) Link to comment Share on other sites More sharing options...
Recommended Posts