cowboys6190 Posted March 10, 2012 Share Posted March 10, 2012 (edited) I am trying to back-up a couple of my 3D blu-rays. I just bought a pack of Digistor 50GB discs (not cheap)... I am trying to burn the ISO copy of the movie and am immediately getting the power calibration area error. This is right at the write leadin phase. I have cleaned the burner out. I have tried a couple different BD-DL from the spindle I just bought. I am only trying to burn at 2X, which is the only supported speed. I have the most current firmware for my drive, at lease that I could find. I have also tried burning a couple other BD 3D ISO's and get the same error. I have been able to burn a non-3D backup to a BD-25 during this time with no problems. I am getting frustrated as this spindle of BD-DL were not cheap. I have tried the last couple in "test mode" so that I would not keep creating expensive coasters. Are my BD drive and BD-DL's not compatible??? If so, what BD drive would be recommended as I do not want these discs to go to waste. Below is one of the logs from my attempts to burn the 3D ISO. I 14:41:04 ImgBurn Version 2.5.6.0 started! I 14:41:04 Microsoft Windows Vista Home Premium Edition (6.0, Build 6002 : Service Pack 2) I 14:41:04 Total Physical Memory: 3,667,528 KB - Available: 2,378,000 KB I 14:41:04 Initialising SPTI... I 14:41:04 Searching for SCSI / ATAPI devices... I 14:41:04 -> Drive 1 - Info: HL-DT-ST BD-RE WH08LS20 2.00-01 (E:) (Fibre) I 14:41:04 -> Drive 2 - Info: SAMSUNG UMS 0001 (G:) (USB) I 14:41:04 Found 1 BD-RE and 1 Unknown! I 14:41:52 Operation Started! I 14:41:52 Source File: F:\Original Movie Sources\Bolt - 3D\BOLT.iso I 14:41:52 Source File Sectors: 16,590,208 (MODE1/2048) I 14:41:52 Source File Size: 33,976,745,984 bytes I 14:41:52 Source File Volume Identifier: BOLT I 14:41:52 Source File Volume Set Identifier: 8CCF6FEC07E934B4_VOLUME_SET_ID I 14:41:52 Source File Application Identifier: APPLICATION_ID I 14:41:52 Source File Implementation Identifier: IMPLEMENTATION_ID I 14:41:52 Source File File System(s): UDF (2.50) I 14:41:52 Destination Device: [2:1:0] HL-DT-ST BD-RE WH08LS20 2.00 (E:) (Fibre) I 14:41:52 Destination Media Type: BD-R (Disc ID: CMCMAG-DI6-000) I 14:41:52 Destination Media Supported Write Speeds: 2x I 14:41:52 Destination Media Sectors: 24,438,784 I 14:41:52 Write Mode: BD I 14:41:52 Write Type: DAO I 14:41:52 Write Speed: 2x I 14:41:52 BD-R Verify Not Required: Yes I 14:41:52 Link Size: Auto I 14:41:52 Lock Volume: Yes I 14:41:52 Test Mode: Yes I 14:41:52 OPC: No I 14:41:52 BURN-Proof: Enabled I 14:41:52 Write Speed Successfully Set! - Effective: 8,991 KB/s (2x) I 14:41:52 Filling Buffer... (40 MB) I 14:41:55 Writing LeadIn... W 14:41:55 Failed to Write Sectors 0 - 31 - Reason: Power Calibration Area Error W 14:41:55 Retrying (1 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (2 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (3 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (4 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (5 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (6 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (7 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (8 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (9 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (10 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (11 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (12 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (13 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (14 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (15 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (16 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (17 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (18 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (19 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error W 14:41:55 Retrying (20 of 20)... W 14:41:55 Retry Failed - Reason: Power Calibration Area Error E 14:41:58 Failed to Write Sectors 0 - 31 - Reason: Power Calibration Area Error I 14:41:58 Synchronising Cache... W 14:42:01 User opted to skip the 'Close Track/Session/Disc' functions. I 14:42:01 Cycling Tray after Test Write... E 14:42:06 Failed to Write Image! E 14:42:08 Operation Failed! - Duration: 00:00:14 I 14:42:08 Average Write Rate: N/A - Maximum Write Rate: N/A Edited March 10, 2012 by cowboys6190 Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted March 10, 2012 Share Posted March 10, 2012 According to the post here... http://club.myce.com/f61/mediacodespeededit-tool-dvd-writers-114269/index48.html#post2513577 ...your drive has no firmware support for the 'CMCMAG-DI6-000' MID. If you can get the 2.00-03 update flashed to it, you should be ok. http://www.firmwarehq.com/download_1857-file_BH08LS20_2.00-03.exe.html Link to comment Share on other sites More sharing options...
cowboys6190 Posted March 10, 2012 Author Share Posted March 10, 2012 (edited) According to the post here... http://club.myce.com/f61/mediacodespeededit-tool-dvd-writers-114269/index48.html#post2513577 ...your drive has no firmware support for the 'CMCMAG-DI6-000' MID. If you can get the 2.00-03 update flashed to it, you should be ok. http://www.firmwarehq.com/download_1857-file_BH08LS20_2.00-03.exe.html Thanks for the reply!!! I have downloaded the .exe file but am not having any luck in flashing it. The program opened but none of my disk drives show up as being available for update. I tried to manually link the .exe to the device driver update screen but that did not work. Any ideas on how I can flash this.... Thanks! Edited March 10, 2012 by cowboys6190 Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted March 10, 2012 Share Posted March 10, 2012 Even my drive shows up in it and it's a BH12LS38.... so your issue is probably related to your controller. Try flashing in safemode. btw, just as the program warns when you attempt it, 'Test Mode' doesn't work for BD-R. At least not on my LG drive it doesn't. Link to comment Share on other sites More sharing options...
Recommended Posts