tony123 Posted November 29, 2007 Posted November 29, 2007 can someone please help imgburn says failed to set write parimeters every time i try to burn a movie after dvdshrink i was ble to burn 1 dvd after downloading imgburn now this happens can someone please help ImgBurn.log
LIGHTNING UK! Posted November 29, 2007 Posted November 29, 2007 You're gonna need to enable I/O debug mode (press the F8 key) AND THEN start a burn so I can see why the command keeps failing. If you've enabled it correctly you should see loads more stuff going into the log window (which you should keep open!). Upload the new log when it's ready. Thanks.
tony123 Posted November 29, 2007 Author Posted November 29, 2007 You're gonna need to enable I/O debug mode (press the F8 key) AND THEN start a burn so I can see why the command keeps failing. If you've enabled it correctly you should see loads more stuff going into the log window (which you should keep open!). Upload the new log when it's ready. Thanks. I did what you said to do with the F8 key and tried to burn here is the new log please help thanks alot ImgBurn.log
LIGHTNING UK! Posted November 29, 2007 Posted November 29, 2007 I'm seeing lots of these errors... Logical Unit Communication CRC Error (ULTRA-DMA/32) To be honest, I've never seen those from USB drives! You might want to double check your cables (and that they're seated properly). I assume it's a real external drive rather than one you've put together yourself? Oh and don't forget to disable I/O debug mode again. It slows things down a lot.
tony123 Posted November 29, 2007 Author Posted November 29, 2007 I'm seeing lots of these errors... Logical Unit Communication CRC Error (ULTRA-DMA/32) To be honest, I've never seen those from USB drives! You might want to double check your cables (and that they're seated properly). I assume it's a real external drive rather than one you've put together yourself? Oh and don't forget to disable I/O debug mode again. It slows things down a lot. it is a real external drive that i bought 4 days ago i was able to burn 2 movies and now the error the cables are seated my other drive that came with the computer burns fine but the new i get these errors i have probably wasted 15 blanks please help
LIGHTNING UK! Posted November 29, 2007 Posted November 29, 2007 There's nothing I can do I'm afraid, this is just some issue with your setup. DMA errors are normally always corrected by replacing the IDE cable to the drive with a decent/new 80 wire one and uninstalling + reinstalling the IDE controller in device manager. With a USB drive, it's not going to be as simple as that. The USB part doesn't have DMA issues so I can only assume it's something inside the enclosure (i.e. between the usb -> ide chip and the drive itself). My advice....take the drive back and get a different one - TOTALLY different.
dontasciime Posted November 29, 2007 Posted November 29, 2007 Try switching to wnaspi32 instead of SPTI in the I/o settings in ImgBurn and also change the usb2 cable. Update the firmware in drive to latest if you have not already. I had the very uncommon Logical Unit Communication CRC Error (ULTRA-DMA/32) whilst using one of my drives in usb enclosure (rare you see this) but fixed it by doing the above OR more than likely swapping enclosure to a different chipset) If after the above you still get those errors send it back and buy a different one. I would avoid getting the exact same one again as if it is chipset related it's gonna do it again. You can download wnaspi32 from nero's site or google it
tony123 Posted November 29, 2007 Author Posted November 29, 2007 Try switching to wnaspi32 instead of SPTI in the I/o settings in ImgBurn and also change the usb2 cable. Update the firmware in drive to latest if you have not already. I had the very uncommon Logical Unit Communication CRC Error (ULTRA-DMA/32) whilst using one of my drives in usb enclosure (rare you see this) but fixed it by doing the above OR more than likely swapping enclosure to a different chipset) If after the above you still get those errors send it back and buy a different one. I would avoid getting the exact same one again as if it is chipset related it's gonna do it again. You can download wnaspi32 from nero's site or google it i do not understand should i return this drive to the store and get a different brand or get the same brand i contacted memorex and they think it i a defective unit after about20 calls to them for support
LIGHTNING UK! Posted November 29, 2007 Posted November 29, 2007 If it's no problem to return it, return it. Even if the 2nd one you have doesn't work, you can still return that and then go for something totally different.
Recommended Posts