Hangs at Synchronising Cache...

[Phlight]

No matter what I try to burn with ImgBurn it always stops at Synchronising Cache... and sits there. Any thoughts???? Thanx in advance!!! Log below.

 

 

 

 

 

I 17:59:19 ImgBurn Version 2.3.2.0 started!

I 17:59:19 Microsoft Windows Vista Ultimate Edition (6.0, Build 6000)

I 17:59:19 Total Physical Memory: 4,117,416 KB - Available: 2,341,192 KB

I 17:59:19 Initialising SPTI...

I 17:59:19 Searching for SCSI / ATAPI devices...

I 17:59:19 Found 2 DVD-ROMs, 1 DVD±RW/RAM and 1 Unknown!

I 18:01:33 Operation Started!

I 18:01:33 Source File: C:\Users\Cedric\Documents\Downloads\PIONEER_CNDV_70MTP_EAST\CNDV_70MTP_EAST.mds

I 18:01:33 Source File Sectors: 3,722,864 (MODE1/2048)

I 18:01:33 Source File Size: 7,624,425,472 bytes

I 18:01:33 Source File Volume Identifier: CNDV_70MTPUC1_A

I 18:01:33 Source File File System(s): ISO9660, UDF (1.02)

I 18:01:33 Destination Device: [0:1:0] TSSTcorp CDDVDW SH-S203N SB01 (D:) (ATAPI)

I 18:01:33 Destination Media Type: DVD+R DL (Disc ID: RICOHJPN-D01-67) (Speeds: 4x, 6x, 8x)

I 18:01:33 Destination Media Sectors: 4,173,824

I 18:01:33 Write Mode: DVD

I 18:01:33 Write Type: DAO

I 18:01:33 Write Speed: MAX

I 18:01:33 Link Size: Auto

I 18:01:33 Test Mode: No

I 18:01:33 BURN-Proof: Enabled

I 18:01:33 Optimal L0 Data Zone Capacity: 1,861,440

I 18:01:33 Optimal L0 Data Zone Method: Copied From Original Disc

I 18:02:18 Filling Buffer... (40 MB)

I 18:02:19 Writing LeadIn...

I 18:02:20 Writing Image... (LBA: 0 - 3722863)

I 18:02:20 Writing Layer 0... (LBA: 0 - 1861439)

I 18:08:29 Writing Layer 1... (LBA: 1861440 - 3722863)

I 18:14:48 Synchronising Cache...

[mmalves]

I 18:01:33 Destination Media Type: DVD+R DL (Disc ID: RICOHJPN-D01-67) (Speeds: 4x, 6x, 8x)

Low quality media. For DVD+R DL media only Verbatim (Made in Singapore) MKM-001-00 is reliable; everything else is hit or miss.

 

If you want to make coasters of the remaining discs, try burning at 6x or 4x and there's a remote chance of success

[LIGHTNING UK!]

SB03 firmware is out now too.

 

When you think it's stuck on the sync cache thing (i.e after no less than 2 mins has passed), press F8 to enable I/O debug mode and look in the log window.

 

If you see I/O commands scrolling up/being added to it then the drive just still thinks it's busy.

 

If you don't see anything, something has died. Check your SATA controller config and drivers. Optical drives like being on controllers set to normal/standard/ata mode rather than RAID or AHCI.

 

Press F8 again to disable I/O debug mode (it slows things down).

[Phlight]

Where did you see the SB03 firmware for the N, I see it for the B but not the N

 

 

SB03 firmware is out now too.

 

When you think it's stuck on the sync cache thing (i.e after no less than 2 mins has passed), press F8 to enable I/O debug mode and look in the log window.

 

If you see I/O commands scrolling up/being added to it then the drive just still thinks it's busy.

 

If you don't see anything, something has died. Check your SATA controller config and drivers. Optical drives like being on controllers set to normal/standard/ata mode rather than RAID or AHCI.

 

Press F8 again to disable I/O debug mode (it slows things down).

[LOCOENG]

I think it must have just been an oversight...all I see is SB01 for the 203N too.

 

http://samsungodd.com/eng/

[LIGHTNING UK!]

Ooops, my bad. I didn't notice the N.

 

There's nothing stopping you from doing what the rest of my post said though.