Jump to content
Sign in to follow this  
palman

invalid field in parameter list

Recommended Posts

hi there

 

i havent had any problems with imgburn for like ages, but today, and i swear my computers know i have a rush job on, i am getting the above error.

 

I first set the the BLP to a 57/43 split on disc where i knew i coudl afford to have it jump to next layer. rather than where is suggest in the middle of a sequence at 50/50

 

i am always consious of having that slight interruption when customers are viewing it back as it changes layer.

 

first i was getting the power calibration error, even though last week i burned another disc fine.

 

so i transfered the image to another computer then i was gettign the l0 zone capacity which i am lost about as to me there is plenty of space on the disc.

 

so as the job has to be out, i remade the iso with the 50/50 split marked good. now i get the error and at a loss how to cure it.

 

i did look through FAQ's but didnt see anything.

 

as this is the first time i have got this error , now i am wondering if its becasuse i updated from 1.23 to 1.29 firmware which i know you guys go a lot on.

Edited by palman

Share this post


Link to post
Share on other sites

i just remade the image again, and tried another 3 dvd's

 

power calibration error again

 

so i tried a 4th dvd and now it finally started burning

 

so a power calibration can be a bad media too? a slightly misleading error perhaps ?

 

i dunno but maybe this thread might help others.

 

it hasnt as yet finished, i may well get error when it changes over to burn L1

Share this post


Link to post
Share on other sites

hiyah

 

i got so many errors i am not 100% sure this is the log from teh one i posted here but it does say the actual error.

 

; //****************************************\\

; ImgBurn Version 2.4.2.0 - Log

; Saturday, 08 November 2008, 10:10:58

; \\****************************************//

;

;

I 10:06:39 ImgBurn Version 2.4.2.0 started!

I 10:06:39 Microsoft Windows XP Professional (5.1, Build 2600 : Service Pack 2)

I 10:06:39 Total Physical Memory: 2,095,852 KB - Available: 1,752,488 KB

I 10:06:39 Initialising SPTI...

I 10:06:39 Searching for SCSI / ATAPI devices...

I 10:06:39 Found 1 DVD

Share this post


Link to post
Share on other sites

it has burned fine but the pause between the layers as it jumps i don't like, i guess there is something simple i missed is choosing the chapter point i actually wanted it to add the BLP too.

Share this post


Link to post
Share on other sites

ahh so what yer saying is the power calibration error , had already written a bit to the disc, thereby not making it not a blank.

 

i did consider that, and took it out to look, as normally you can see where its been written, i guess it was so small an area it didnt show up to well.

 

Thankyou again for your input and i know you keep harping on about dvd's but i rarely have problems with the Fortis brand, even on xbox360. I do tend to use a 10 bank duplicator but i still need to make the master, i don't have the usb addon.

 

I have since writing to the forum, had to bin all i did and start from scratch, and i am pleased to say all went well this time. Yes using the same brand disc :P heh i am sure you have shares in verbatim. Actually they are very good discs and i do have a few here in stock. The problem is the customers just pirate the ruddy dvd's anyway :(. It is about time to see they dropped down in price too.

 

thx again

Share this post


Link to post
Share on other sites

It looks as the media code you are using is not included in the 1.29 firmware version.

 

I 10:07:15 Destination Media Type: DVD+R DL (Disc ID: CMC MAG-D02-00) (Speeds: 2.4x)

 

post-20-1226158645_thumb.png

 

It's supported in the DVR-216D model:

 

post-20-1226159056_thumb.png

Share this post


Link to post
Share on other sites
Sign in to follow this  

×

Important Information

By using this site, you agree to our Terms of Use.