LIGHTNING UK! Posted December 24, 2016 Share Posted December 24, 2016 The defaults work fine. There's very little to actually configure for burning discs. The drive and firmware control all the technical stuff. Software pretty much just sends the data. Link to comment Share on other sites More sharing options...
gamercr7 Posted December 24, 2016 Author Share Posted December 24, 2016 (edited) 1 virtual clonedrive or daemon tools can disrupt the dvd drive and disrupt disk burning? disable drive of the virtual e daemon tools? 2 is it possible to restore imgburn settings? 3 Does my lite-on drive iHAS122-14 FU frmware EL06 have any updates available? Edited December 24, 2016 by gamercr7 Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted December 24, 2016 Share Posted December 24, 2016 1. No 2. Yes, using the aptly named 'Restore Defaults' button within the settings. 3. No Link to comment Share on other sites More sharing options...
gamercr7 Posted December 24, 2016 Author Share Posted December 24, 2016 Can active processes in windows 10 damage the burning or scandisc of dvd? How do you disable them? Link to comment Share on other sites More sharing options...
Ch3vr0n Posted December 24, 2016 Share Posted December 24, 2016 No they can't. Disable via task manager, but if you don't know EXACTLY what you're doing you'll cause system instability. You just don't give up do you? More and more questions way beyond op. Sent from my Nexus 6P with Tapatalk. Link to comment Share on other sites More sharing options...
gamercr7 Posted December 24, 2016 Author Share Posted December 24, 2016 How to burn a disk in imgburn showing folder? Already burned disks in imgburn, I had the files in folder but after burning the disk they did not stay in the folder inside the disk Link to comment Share on other sites More sharing options...
Ch3vr0n Posted December 24, 2016 Share Posted December 24, 2016 Again not related to burn errors. Why do you keep going further away from the original issue. Different 'questions' : different topic Mode selector - burn folders to disc - done. Imgburn burns exactly what you tell it to burn. If you select a folder it will burn the folder and it's contents. If you only select the folder contents then it only burns that. It's not possible that you select a folder with contents and imgburn only burning the contents and not the folder too. Anyway out for good now. No doubt after this round of questions you'll come up with some more, again not related to the original topic questions. Cya Sent from my Nexus 6P with Tapatalk. Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted December 25, 2016 Share Posted December 25, 2016 Actually, that can happen if you're in standard input mode and only add 1 folder. It'll prompt you to ask if that folder represents what should be the root folder of the disc. What happens to that folder then depends on your answer. I don't mind if the op asks extra questions in their topic. I'd rather that than them hijack someone else's. Link to comment Share on other sites More sharing options...
gamercr7 Posted December 25, 2016 Author Share Posted December 25, 2016 I do not know which root option to choose, I want to insert the disk to show the folder Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted December 25, 2016 Share Posted December 25, 2016 Ok, so I added 1 folder to the little 'source' box. When I go the burn the disc, I'm presented with this messagebox. It's relatively clear to me as to what I'd do in your situation, but I realise you're not a native speaker of the English language. You'd need to click 'No' if you want the actual folder in the root of the disc. Link to comment Share on other sites More sharing options...
gamercr7 Posted December 25, 2016 Author Share Posted December 25, 2016 1 I click option "no" burn the disk and insert the disk in the drive will appear the folder with all the files inside it? 2 if I click "Yes" option burn the disk and insert the disk into the drive will only appear the files and the folder does not appear? Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted December 25, 2016 Share Posted December 25, 2016 Correct Link to comment Share on other sites More sharing options...
gamercr7 Posted December 25, 2016 Author Share Posted December 25, 2016 I'm going to burn mdisc verbatim using imgburn, do you have any option to check if you have any burning error and see jitter, pie, pif, pof? Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted December 25, 2016 Share Posted December 25, 2016 The drive will either error out during the 'write' operation or the verify one. Just make sure the verify box is checked so it does actually do that bit. Do the pipo tests with the normal software. Link to comment Share on other sites More sharing options...
gamercr7 Posted December 25, 2016 Author Share Posted December 25, 2016 (edited) 1 in mdisc verbatim is it possible to use imgburn "verify" and nero discspeed disc quality and read test surface? 2 What are your recommendations for the best burning quality of mdisc? 3 A common dvd-r 16x disc showing PIE values 60, 132, 138, 163, 181, 152, 165, 181, 169, 178, 164, 179, 159, 150, 162, 190, 194, 201, 205, and Jitter of 12%, it is possible to extract all the contents of this dvd or the files of that dvd will be corrupted because of the high PIE and high jitter? 4 windows 10 system and its automatic processes and automatic software processes can influence performance scan Disc Quality (PIE, PIF, jitter, POF) of Nero DiscSpeed 5? Edited December 25, 2016 by gamercr7 Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted December 25, 2016 Share Posted December 25, 2016 1. Yes, verify is not limited to certain disc formats. I don't know about discspeed, that could be more of a firmware / chipset thing as the software issues vendor unique commands in order to get pipo levels. 2. I don't have any. 3. If verify passes, it's readable. 4. They shouldn't, no. Link to comment Share on other sites More sharing options...
gamercr7 Posted December 25, 2016 Author Share Posted December 25, 2016 (edited) 1 in mdisc this writing 4x write, I burn it in 2x for better results? 2 Which verification did you mention? Imgburn verify the disk passed ok, nero discspeed 5 read test surface the disk passed ok 100% good, However but high jitter and PIE high remain 3 a dvd-r 16x verbatim azo mcc with high jitter: 12%, High PIE: 205 will die early compared to a dvd-r disc 16x verbatim azo mcc with jitter 9%, PIE: 45? 4 some people have told me that a process in use can modify the jitter, pie, pif, dvd scan pof reading Edited December 25, 2016 by gamercr7 Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted December 26, 2016 Share Posted December 26, 2016 1. We've already covered this. You won't find the best speed until you burn a few at each and test them. 2. There's only 1 in ImgBurn. Like I said, make sure the 'verify' checkbox is ticked. 3. I'd expect a disc that's better to begin with will last longer, yes. That's assuming everything else about them and the storage methods is identical. 4. The error levels are reported by the drive. A process on your pc shouldn't alter what is an internal function of the drive and the media in it. Link to comment Share on other sites More sharing options...
gamercr7 Posted December 26, 2016 Author Share Posted December 26, 2016 1 For the longevity of the disk and files Is the make and manufacturer of the disk more important than jitter, PIE, PIF, POF? A disc verbatim dvd-r 16x azo mcc 03rg20 with high PIE (207), high jitter (12%), high PIF will last longer than a dvd + r philips disc with low jitter, low PIE, low PIF or philips goes Last longer? 2 mdisc has already been tested to prove its durability and resistance to moisture, light, heat? Does the plicarbonate and glue break the test? Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted December 26, 2016 Share Posted December 26, 2016 No idea Link to comment Share on other sites More sharing options...
gamercr7 Posted December 26, 2016 Author Share Posted December 26, 2016 Is it good for me to activate the OPC option? Power calibration Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted December 27, 2016 Share Posted December 27, 2016 Please refer to my answer in post 29. Link to comment Share on other sites More sharing options...
gamercr7 Posted December 27, 2016 Author Share Posted December 27, 2016 I read the post but there are people who say that OPC prevents a burning with errors Link to comment Share on other sites More sharing options...
LIGHTNING UK! Posted December 27, 2016 Share Posted December 27, 2016 That's the beauty of the Internet. It'll tell you everything you want to read and everything you don't want to read. Link to comment Share on other sites More sharing options...
gamercr7 Posted December 28, 2016 Author Share Posted December 28, 2016 What is the best configuration of imgburn for the best burning in the media? Is there a better setting? Link to comment Share on other sites More sharing options...
Recommended Posts